Infiniti G37 Coupe. Manual — part 704
EXT-30
< ON-VEHICLE REPAIR >
FLOOR SIDE FAIRING
2.
Remove rear under cover.
INSTALLATION
Install in the reverse order of removal.
![](/vehicles/zatt/keash/ckiif/can.png)
ROOF SIDE MOLDING
EXT-31
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000001677490
Removal and Installation
INFOID:0000000001677491
REMOVAL
Disengage roof side molding (1) fixing clips with remover tool (A).
CAUTION:
Wrap the tip of remover tool (A) with a cloth (B).
INSTALLATION
Install from roof side molding rear end to front end in this order after temporarily holding.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding.
1.
Roof side molding
2.
Roof side molding clip
3.
Body side panel
4.
Roof panel
JMKIA1245ZZ
: Clip
JMKIA1246ZZ
EXT-32
< ON-VEHICLE REPAIR >
ROOF SIDE MOLDING
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• Use double-faced adhesive tape after hardening for clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Do not wash the vehicle with in 24 hours so as to keep adhesive.
Adhesive
: 3M–weld DP-100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
![](/vehicles/zatt/keash/ckiif/cande.png)
FRONT PILLAR FINISHER
EXT-33
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT PILLAR FINISHER
Exploded View
INFOID:0000000001725462
Refer to
for symbols in the figure.
Removal and Installation
INFOID:0000000001725463
Removal
1.
Remove clip and double faced adhesive tapes of body side weather-strip.
2.
Remove body side weather-strip.
1.
Front pillar finisher
2.
Body side weather-strip retainer
3.
Body side weather-strip
4.
Grommet
5.
Body side outer
6.
Double-faced adhesive tape
[t: 1.2 mm (0.047 in)]
7.
Double-faced adhesive tape
[t: 0.4 mm (0.016 in)]
: Clip
JMKIA1247ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст