Infiniti Q45 (FY33). Manual — part 179
![](/vehicles/zatt/fitanyou/tushi/xpo.png)
Fuel Injection System Function (Lean side)
(P0171: Bank 1), (P0174: Bank 2)
ON BOARD DIAGNOSIS LOGIC
With the Air/Fuel Mixture Ratio Self-Learning Control, the actual mixture ratio can be brought closely to the
theoretical mixture ratio based on the mixture ratio feedback signal from the heated oxygen sensor 1 (front).
The ECM calculates the necessary compensation to correct the offset between the actual and the theoretical
ratios.
In case the amount of the compensation value is extremely large (The actual mixture ratio is too lean.), the
ECM judges the condition as the fuel injection system malfunction and light up the MIL (2 trip detection logic).
Heated oxygen sensor 1 (front)
E
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
ECM
E
Injectors
Diagnostic Trouble
Code No.
Malfunction is detected when ...
Check Items
(Possible Cause)
P0171
0115
(Bank 1)
I
Fuel injection system does not operate properly.
I
The amount of mixture ratio compensation is too large. (The
mixture ratio is too lean.)
I
Intake air leaks
I
Heated oxygen sensor 1 (front)
I
Injectors
I
Exhaust gas leaks
I
Incorrect fuel pressure
I
Lack of fuel
I
Mass air flow sensor
P0174
0210
(Bank 2)
SEF985Z
SEC042C
DIAGNOSTIC TROUBLE CODE CONFIRMATION
PROCEDURE
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DURE” has been previously conducted, always turn ignition
switch “OFF” and wait at least 5 seconds before conducting
the next test.
1) Start engine and warm it up to normal operating tem-
perature.
2) Turn ignition switch “OFF” and wait at least 5 seconds.
3) Turn ignition switch “ON” and select “SELF-LEARN
CONTROL” in “WORK SUPPORT” mode with CON-
SULT-II.
4) Clear the self-learning control coefficient by touching
“CLEAR”.
5) Select “DATA MONITOR” mode with CONSULT-II.
6) Start engine again and let it idle for at least 10 minutes.
The 1st trip DTC P0171 should be detected at this
stage, if a malfunction exists. If so, go to “DIAGNOSTIC
PROCEDURE”, EC-249.
7) If it is difficult to start engine at step 6), the fuel injec-
tion system has a malfunction.
8) Crank engine while depressing accelerator pedal. If
engine starts, go to “DIAGNOSTIC PROCEDURE”,
EC-249. If engine does not start, visually check for
exhaust and intake air leak.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ OR ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
GI
MA
EM
LC
FE
AT
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
TROUBLE DIAGNOSIS FOR DTC P0171 (B1), P0174 (B2)
EC-245
![](/vehicles/zatt/fitanyou/tushi/selast.png)
SEF395W
1) Start engine and warm it up to normal operating tem-
perature.
2) Turn ignition switch “OFF” and wait at least 5 seconds.
3) Disconnect mass air flow sensor harness connector.
Then restart and run engine for at least 3 seconds at
idle speed.
4) Stop engine and reconnect mass air flow sensor har-
ness connector.
5) Select “MODE 7” with GST. Make sure 1st trip DTC
P0100 is detected.
6) Select “MODE 4” with GST and erase the 1st trip DTC
P0100.
7) Start engine again and run it for at least 10 minutes at
idle speed.
8) Select “MODE 7” with GST. The 1st trip DTC P0171
should be detected at this stage, if a malfunction exists.
If so, go to “DIAGNOSTIC PROCEDURE”, EC-249.
9) If it is difficult to start engine at step 8, the fuel injection
system has a malfunction.
10) Crank engine while depressing accelerator pedal.
If engine starts, go to “DIAGNOSTIC PROCEDURE”,
EC-249.
If the engine does not start, visually check for exhaust
and intake air leak.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ OR ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1) Start engine and warm it up to normal operating tem-
perature.
2) Turn ignition switch “OFF” and wait at least 5 seconds.
3) Disconnect mass air flow sensor harness connector.
Then restart engine and run it at least 3 seconds at idle
speed.
4) Stop engine and reconnect mass air flow sensor har-
ness connector.
5) Turn ignition switch “ON”.
6) Perform “Diagnostic Test Mode II (Self-diagnostic
results)” with ECM. Make sure DTC 0102 is detected.
7) Erase the DTC 0102 by changing from Diagnostic Test
Mode II to Diagnostic Test Mode I.
8) Perform “Diagnostic Test Mode II (Self-diagnostic
results)” with ECM. Make sure DTC 0505 is detected.
9) Start engine again and run it for at least 10 minutes at
idle speed.
The DTC 0115 should be detected at this stage, if a
malfunction
exists.
If
so,
go
to
“DIAGNOSTIC
PROCEDURE”, EC-249.
10) If it is difficult to start engine at step 9, the fuel injection
system also has a malfunction.
11) Crank engine while depressing accelerator pedal.
If engine starts, go to “DIAGNOSTIC PROCEDURE”,
EC-249.
If the engine does not start, visually check for exhaust
and intake air leak.
TROUBLE DIAGNOSIS FOR DTC P0171 (B1), P0174 (B2)
Fuel Injection System Function (Lean side)
(P0171: Bank 1), (P0174: Bank 2) (Cont’d)
EC-246
![](/vehicles/zatt/fitanyou/tushi/kil.png)
BANK 1
TEC791
GI
MA
EM
LC
FE
AT
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
TROUBLE DIAGNOSIS FOR DTC P0171 (B1), P0174 (B2)
Fuel Injection System Function (Lean side)
(P0171: Bank 1), (P0174: Bank 2) (Cont’d)
EC-247
![](/vehicles/zatt/fitanyou/tushi/whe.png)
BANK 2
TEC793
TROUBLE DIAGNOSIS FOR DTC P0171 (B1), P0174 (B2)
Fuel Injection System Function (Lean side)
(P0171: Bank 1), (P0174: Bank 2) (Cont’d)
EC-248
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст