Infiniti M35/M45 Y50. Manual — part 1022
![](/vehicles/zatt/cen/houeebante/quee.png)
SIDE OIL SEAL
RFD-15
C
E
F
G
H
I
J
K
L
M
A
B
RFD
3.
Install side flange with the following procedure.
a.
Attach the protector to side oil seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put a suitable drift on the center of side flange, then drive it until
sound changes.
NOTE:
When installation is completed, driving sound of the side flange
turns into a sound which seems to affect the whole final drive.
d.
Confirm that the dimension of the side flange installation (Mea-
surement A) in the figure comes into the following.
4.
Install drive shaft. Refer to
.
5.
Install rear wheel sensor. Refer to
.
6.
Install center muffler. Refer to
.
7.
When oil leaks while removing, check oil level after the installation. Refer to
.
Tool number
: KV38107900 (J-39352)
SDIA0822E
Measurement A: 326 - 328 mm (12.83 - 12.91 in)
SDIA1039E
![](/vehicles/zatt/cen/houeebante/seanake.png)
RFD-16
REAR FINAL DRIVE ASSEMBLY
REAR FINAL DRIVE ASSEMBLY
PFP:38300
Removal and Installation
NDS000F7
COMPONENTS
REMOVAL
1.
Remove center muffler with a power tool. Refer to
2.
Remove rear stabilizer bar with a power tool. Refer to
.
3.
Remove propeller shaft from the final drive. Refer to
PR-8, "Removal and Installation"
.
4.
Remove drive shaft from final drive with a power tool. Then sus-
pend it by wire etc. Refer to
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
1.
Rear final drive assembly
2.
Upper stopper
3.
Propeller shaft
4.
Washer
5.
Lower stopper
6.
Drive shaft
A: For VQ35DE models
B: For VK45DE models
, for the symbols in the figure.
PDIA0967E
SDIA1094E
![](/vehicles/zatt/cen/houeebante/nge.png)
REAR FINAL DRIVE ASSEMBLY
RFD-17
C
E
F
G
H
I
J
K
L
M
A
B
RFD
7.
Set a suitable jack to rear final drive assembly.
CAUTION:
Do not place a suitable jack on the rear cover (aluminum
case).
8.
Remove the mounting bolts and nuts connecting to the suspen-
sion member, and remove rear final drive assembly with a power
tool.
CAUTION:
Secure rear final drive assembly to a suitable jack while
removing it.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
●
Refer to
about each tightening torque.
●
When installing breather hoses (1), refer to the figure.
CAUTION:
Make sure there are no pinched or restricted areas on the
breather hose caused by bending or winding when install-
ing it.
–
For installation, the vehicle side end shall be inserted to suspen-
sion member (2). Install metal connector (3) side of this hose to
rear cover by inserting it with aiming painted marking to the front
of vehicle.
●
When oil leaks while removing final drive assembly, check oil
level after the installation. Refer to
.
SDIA1969J
SDIA1970J
PDIA0754E
![](/vehicles/zatt/cen/houeebante/usumeng.png)
RFD-18
REAR FINAL DRIVE ASSEMBLY
Disassembly and Assembly
NDS000F8
COMPONENTS
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Gear carrier
6.
Side oil seal
7.
Side flange
8.
Collapsible spacer
9.
Pinion rear bearing
10. Pinion height adjusting washer
11.
Drive pinion
12. Side bearing adjusting washer
13. Side bearing
14. Side gear thrust washer
15. Circular clip
16. Side gear
17. Lock pin
18. Pinion mate gear
19. Pinion mate thrust washer
20. Pinion mate shaft
21. Drive gear
22. Differential case
23. Bearing cap
24. Filler plug
25. Gasket
26. Rear cover
27. Drain plug
A: Oil seal lip
B: Screw hole
C: After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.
and the followings for the symbols in the figure.
:
Apply gear oil.
:
Apply anti-corrosion oil.
:
Apply Genuine Silicone RTV or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
:
Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-47, "Recommended Chemical Prod-
PDIA0986E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст