Infiniti M35/M45 Y50. Manual — part 96
![](/vehicles/zatt/cen/houeebante/yowok.png)
DISASSEMBLY
AT-307
D
E
F
G
H
I
J
K
L
M
A
B
AT
29. Remove oil pan, oil pan gasket and clips (VQ35DE models) or oil pan, oil pan gasket, brackets and clips
(VK45DE models) according to the following procedures.
a.
VQ35DE models
i.
Remove clips (1).
ii.
Remove oil pan (2) and oil pan gasket.
: Front
: Bolt (22)
b.
VK45DE models
i.
Remove clips (1) and brackets (2).
ii.
Remove oil pan (3) and oil pan gasket.
: Front
: Bolt (22)
30. Check foreign materials in oil pan to help determine causes of
malfunction. If the ATF is very dark, smells burned, or contains
foreign particles, the frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.
●
If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
AT-14, "A/T Fluid Cooler Cleaning"
.
31. Remove magnets from oil pan.
SCIA8039E
SCIA8035E
SCIA5199E
SCIA5200E
![](/vehicles/zatt/cen/houeebante/med.png)
AT-308
DISASSEMBLY
32. Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
33. Straighten terminal clips to free terminal cord assembly and A/T
fluid temperature sensor 2 harness.
34. Disconnect revolution sensor connector.
CAUTION:
Be careful not to damage connector.
35. Straighten terminal clip to free revolution sensor harness.
36. Remove bolts A, B and C from control valve with TCM.
SCIA5023E
SCIA5446E
SCIA7524E
SCIA7526E
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5025E
![](/vehicles/zatt/cen/houeebante/ntendockiof.png)
DISASSEMBLY
AT-309
D
E
F
G
H
I
J
K
L
M
A
B
AT
37. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
38. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
39. Remove bracket from A/T fluid temperature sensor 2.
40. Remove O-ring from A/T assembly harness connector.
41. Disconnect TCM connectors.
CAUTION:
Be careful not to damage connectors.
SCIA5260E
SCIA5301E
SCIA5264E
SCIA5155E
SCIA5447E
![](/vehicles/zatt/cen/houeebante/dall.png)
AT-310
DISASSEMBLY
42. Remove A/T assembly harness connector from control valve
with TCM using a flat-bladed screwdriver.
43. Disconnect TCM connector and park/neutral position switch
connector.
CAUTION:
Be careful not to damage connectors.
44. Remove one of the following parts.
●
Rear extension assembly (VQ35DE models for 2WD)
●
Output shaft & companion flange complement (VK45DE models for 2WD)
●
Adapter case assembly (AWD models)
a.
VQ35DE models for 2WD
i.
Remove tightening bolts for rear extension assembly and trans-
mission case.
ii.
Tap rear extension assembly with a soft hammer.
SCIA5448E
SCIA5449E
SCIA6941E
SCIA5028E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст