Infiniti M35/M45 Y50. Manual — part 578
![](/vehicles/zatt/cen/houeebante/rnt.png)
BASIC SERVICE PROCEDURE
EC-785
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
17.
DETECT MALFUNCTIONING PART
Check the following.
●
Check camshaft position sensor (PHASE) and circuit. Refer to
EC-1082, "DTC P0340 CAMSHAFT POSI-
●
Check crankshaft position sensor (POS) and circuit. Refer to
EC-1075, "DTC P0335 CKP SENSOR
OK or NG
OK
>> GO TO 18.
NG
>> 1. Repair or replace.
2. GO TO 4.
18.
CHECK ECM FUNCTION
1.
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is a rare case.)
2.
Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs. Refer to
BL-248, "ECM Re-Communicating Function"
>> GO TO 4.
19.
INSPECTION END
Did you replace ECM, referring this Basic Inspection procedure?
Yes or No
Yes
>> 1. Perform
.
2. INSPECTION END
No
>> INSPECTION END
Idle Speed and Ignition Timing Check
NBS005A7
IDLE SPEED
With CONSULT-II
Check idle speed in “DATA MONITOR” mode with CONSULT-II.
With GST
Check idle speed with GST.
IGNITION TIMING
Any of following two methods may be used.
SEF058Y
![](/vehicles/zatt/cen/houeebante/urd.png)
EC-786
[VK45DE]
BASIC SERVICE PROCEDURE
Method A
1.
Attach timing light A to loop wire (1) as shown.
2.
Check ignition timing.
●
Timing indicator (1)
Method B
1.
Remove ignition coil No. 1 (1).
2.
Connect ignition coil No. 1 (1) and spark plug No. 1 with suitable
high-tension wire A as shown, and attach timing light clamp B to
this wire.
PBIB2717E
PBIB2719E
PBIB2716E
PBIB2718E
![](/vehicles/zatt/cen/houeebante/athe.png)
BASIC SERVICE PROCEDURE
EC-787
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
Check ignition timing.
●
Timing indicator (1)
Procedure After Replacing ECM
NBS005SH
When replacing ECM, the following procedure must be performed.
1.
Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs.
Refer to
BL-248, "ECM Re-Communicating Function"
2.
Perform
3.
Perform
EC-788, "Accelerator Pedal Released Position Learning"
4.
Perform
EC-788, "Throttle Valve Closed Position Learning"
5.
Perform
EC-788, "Idle Air Volume Learning"
VIN Registration
NBS005A9
DESCRIPTION
VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced.
NOTE:
Accurate VIN which is registered in ECM may be required for Inspection & Maintenance (I/M).
OPERATION PROCEDURE
With CONSULT-II
1.
Check the VIN of the vehicle and note it. Refer to
GI-48, "IDENTIFICATION INFORMATION"
2.
Turn ignition switch ON and engine stopped.
3.
Select “VIN REGISTRATION” in “WORK SUPPORT” mode.
4.
Follow the instruction of CONSULT-II display.
SEF166Y
PBIB2719E
PBIB2242E
![](/vehicles/zatt/cen/houeebante/gitokasine.png)
EC-788
[VK45DE]
BASIC SERVICE PROCEDURE
Accelerator Pedal Released Position Learning
NBS005AA
DESCRIPTION
Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accel-
erator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time
harness connector of accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1.
Make sure that accelerator pedal is fully released.
2.
Turn ignition switch ON and wait at least 2 seconds.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Repeat steps 2 and 3 four times.
Throttle Valve Closed Position Learning
NBS005AB
DESCRIPTION
Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by
monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1.
Make sure that accelerator pedal is fully released.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning
NBS005AC
DESCRIPTION
Idle Air Volume Learning is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:
●
Each time electric throttle control actuator or ECM is replaced.
●
Idle speed or ignition timing is out of specification.
PREPARATION
Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
●
Battery voltage: More than 12.9V (At idle)
●
Engine coolant temperature: 70 - 105
°
C (158 - 221
°
F)
●
PNP switch: ON
●
Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine
is started the headlamp will not be illuminated.
●
Steering wheel: Neutral (Straight-ahead position)
●
Vehicle speed: Stopped
●
Transmission: Warmed-up
–
With CONSULT-II: Drive vehicle until “ATF TEMP SE 1” in “DATA MONITOR” mode of “A/T” system indi-
cates less than 0.9V.
–
Without CONSULT-II: Drive vehicle for 10 minutes.
OPERATION PROCEDURE
With CONSULT-II
1.
Perform
EC-788, "Accelerator Pedal Released Position Learning"
2.
Perform
EC-788, "Throttle Valve Closed Position Learning"
.
3.
Start engine and warm it up to normal operating temperature.
4.
Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст