Infiniti M35/M45 Y50. Manual — part 108
ASSEMBLY
AT-355
D
E
F
G
H
I
J
K
L
M
A
B
AT
iv.
Install bearing race to output shaft.
v.
Install gasket onto transmission case.
CAUTION:
●
Completely remove all moisture, oil and old gasket, etc.
from the transmission case and adapter case assembly
mounting surfaces.
●
Do not reuse gasket.
vi. Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the adapter
case assembly.
vii. Tighten adapter case assembly bolts (1) to the specified torque.
[With bracket (2).] Refer to
: Bolt (10)
CAUTION:
Do not reuse self-sealing bolts (3).
Refer to GI section to make sure icons (symbol marks) in the fig-
ure. Refer to
SCIA5245E
SCIA5231E
SCIA5186E
SCIA6910E
AT-356
ASSEMBLY
27. Install needle bearing in drum support.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
28. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
29. Install high and low reverse clutch assembly in direct clutch.
30. Using a flat-bladed screwdriver, align the drive plate.
31. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5198E
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E
ASSEMBLY
AT-357
D
E
F
G
H
I
J
K
L
M
A
B
AT
CAUTION:
Make sure that portion “A” of high and low reverse clutch
drum protrudes approximately 2 mm (0.08 in) beyond por-
tion “B” of rear sun gear.
32. Install needle bearing in rear carrier assembly.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
33. Install bearing race in rear carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
34. Install rear carrier assembly in direct clutch drum.
SCIA3130E
SCIA2803E
SCIA5175E
SCIA2462E
AT-358
ASSEMBLY
35. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
36. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
37. Install mid carrier assembly in rear carrier assembly.
38. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
39. Install seal rings in input clutch assembly.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
SCIA2804E
SCIA2805E
SCIA5017E
SCIA5015E
SCIA2470E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст