Infiniti M35/M45 Y50. Manual — part 106
![](/vehicles/zatt/cen/houeebante/you.png)
ASSEMBLY
AT-347
D
E
F
G
H
I
J
K
L
M
A
B
AT
15. Install seal rings to drum support.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
16. Install spring retainer and return spring in transmission case.
17. Set the SST on spring retainer and install snap ring (fixing spring
retainer) in transmission case while compressing return spring.
CAUTION:
Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.
18. Install reverse brake drive plates, driven plates and dish plates
in transmission case.
CAUTION:
Take care with order of plates.
●
Snap ring (1)
●
Retaining plate (2)
●
Drive plate (3)
●
Driven plate (4)
●
Dish plate (5)
●
Drive plate/Driven plate: 6/6
SCIA3333E
SCIA2324E
SCIA5877E
SCIA6949E
![](/vehicles/zatt/cen/houeebante/kyo.png)
AT-348
ASSEMBLY
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
22. Measure clearance between retaining plate and snap ring. If not
within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
SCIA5249E
SCIA2439E
Specified clearance A
Standard: 0.7 - 1.1 mm (0.028 - 0.043 in)
Retaining plate
Refer to
.
SCIA3129E
SCIA5031E
![](/vehicles/zatt/cen/houeebante/foo.png)
ASSEMBLY
AT-349
D
E
F
G
H
I
J
K
L
M
A
B
AT
24. Install revolution sensor to transmission case. Tighten revolution
sensor bolt to the specified torque. Refer to
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.
●
Do not place in an area affected by magnetism.
25. Assemble one of the following parts.
●
Rear extension assembly (VQ35DE models for 2WD)
●
Adapter case assembly (AWD models)
●
Output shaft & companion flange complement (VK45DE models for 2WD)
a.
VQ35DE models
i.
As shown in the figure, use the drift to drive rear oil seal into the
rear extension (2WD models) or adapter case (AWD models)
until it is flush.
CAUTION:
●
Apply ATF to rear oil seal.
●
Do not reuse rear oil seal.
ii.
Install return spring (1) to parking pawl (2).
SCIA2320E
SCIA5477E
SCIA6180J
![](/vehicles/zatt/cen/houeebante/xxcafito.png)
AT-350
ASSEMBLY
iii.
Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (AWD models).
iv.
Install parking actuator support from rear extension (2WD mod-
els) or adapter case (AWD models).
v.
Install needle bearing (1) to rear extension (2WD models) or
adapter case (AWD models).
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
Refer to GI section to make sure icons (symbol marks) in the fig-
ure. Refer to
.
b.
VK45DE models
i.
Install return spring (1) to parking pawl (2).
SCIA3424E
SCIA3423E
SCIA6179J
SCIA6180J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст