Infiniti M35/M45 Y50. Manual — part 544
DTC P2A00, P2A03 A/F SENSOR 1
EC-649
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
2
SB
A/F sensor 1 heater
(bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
16
G/W
A/F sensor 1 (bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 3.1V
35
BR/W
Approximately 2.6V
56
G
Approximately 2.3V
75
GR
Approximately 2.3V
PBIB1584E
EC-650
[VQ35DE]
DTC P2A00, P2A03 A/F SENSOR 1
BANK 2
TBWT0980E
DTC P2A00, P2A03 A/F SENSOR 1
EC-651
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
NBS0057M
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten two ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
24
O
A/F sensor 1 heater
(bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
57
GR/L
A/F sensor 1 (bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 2.6V
58
LG/B
Approximately 2.3V
76
W/L
Approximately 3.1V
77
Y
Approximately 2.3V
PBIB1584E
1.
Body ground M70
2.
Body ground M16
PBIB2782E
EC-652
[VQ35DE]
DTC P2A00, P2A03 A/F SENSOR 1
2.
RETIGHTEN A/F SENSOR 1
1.
Loosen and retighten the A/F sensor 1.
>> GO TO 3.
3.
CHECK FOR INTAKE AIR LEAK
1.
Start engine and run it at idle.
2.
Listen for an intake air leak after the mass air flow sensor.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace.
Tightening torque: 50 N-m (5.1 kg-m, 37 ft-lb)
PBIB2200E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст