Infiniti M35/M45 Y50. Manual — part 550
FUEL INJECTOR
EC-673
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
5.
CHECK FUNCTION OF FUEL INJECTOR-II
Provide battery voltage between the following terminals, and then
interrupt it. Listen to each fuel injector operating sound.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK SUB-HARNESS CIRCUIT FOR OPEN AND SHORT
1.
Disconnect fuel injector harness connector (1).
2.
Check harness continuity between the following terminals. Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
Cylinder
Harness connector F221 terminal
(+)
(–)
1
5
6
2
4
3
2
4
3
5
1
6
7
Operating sound should exist.
PBIB2497E
PBIB2792E
Harness connector F221 terminal
Fuel injector terminal
1
2
2
3
4
6
7
5
1
Continuity should exist.
EC-674
[VQ35DE]
FUEL INJECTOR
7.
CHECK FUEL INJECTOR
Refer to
EC-674, "Component Inspection"
OK or NG
OK
>> GO TO 8.
NG
>> Replace malfunctioning fuel injector.
8.
CHECK INTERMITTENT INCIDENT
Refer to
EC-153, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
NBS0057X
FUEL INJECTOR
1.
Disconnect fuel injector harness connector.
2.
Check resistance between terminals as shown in the figure.
Removal and Installation
NBS0057Y
FUEL INJECTOR
Refer to
EM-47, "FUEL INJECTOR AND FUEL TUBE"
Resistance: 11.1 - 14.5
Ω
[at 10 - 60
°
C (50 - 140
°
F)]
PBIB1727E
FUEL PUMP
EC-675
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
FUEL PUMP
PFP:17042
Description
NBS0057Z
SYSTEM DESCRIPTION
*: ECM determines the start signal status by the signals of engine speed and battery voltage.
The ECM activates the fuel pump for several seconds after the ignition switch is turned ON to improve engine
startability. If the ECM receives a engine speed signal from the camshaft position sensor (PHASE), it knows
that the engine is rotating, and causes the pump to operate. If the engine speed signal is not received when
the ignition switch is ON, the engine stalls. The ECM stops pump operation and prevents battery discharging,
thereby improving safety. The ECM does not directly drive the fuel pump. It controls the ON/OFF fuel pump
relay, which in turn controls the fuel pump.
COMPONENT DESCRIPTION
A turbine type design fuel pump is used in the fuel tank.
●
Fuel level sensor unit and fuel pump (1)
●
Fuel pressure regulator (2)
●
Fuel tank temperature sensor (3)
CONSULT-II Reference Value in Data Monitor Mode
NBS00580
Specification data are reference values.
Sensor
Input signal to ECM
ECM Function
Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
Fuel pump control
Fuel pump relay
Battery
Battery voltage*
Condition
Fuel pump operation
Ignition switch is turned to ON.
Operates for 1 second.
Engine running and cranking
Operates.
When engine is stopped
Stops in 1.5 seconds.
Except as shown above
Stops.
PBIB2707E
MONITOR ITEM
CONDITION
SPECIFICATION
FUEL PUMP RLY
●
For 1 seconds after turning ignition switch: ON
●
Engine running or cranking
ON
●
Except above
OFF
EC-676
[VQ35DE]
FUEL PUMP
Wiring Diagram
NBS00581
TBWT1535E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст