Mitsubishi Lancer Evolution IX. Manual — part 209
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-95
COMMENTS ON TROUBLE SYMPTOM
If the front passenger's or rear power window does
not work by means of the respective power window
sub switch, the power window sub switch or the
power window regulator motor may be defective.
POSSIBLE CAUSES
• Malfunction of the front power window sub switch
(RH) <LH drive vehicles>, front power window
sub switch (LH) <RH drive vehicles>, power win-
dow sub switch (rear: RH) or power window sub
switch (rear: LH)
FUSIBLE
LINK
5
POWER
WINDOW
RELAY
ETACS-ECU
POWER
WINDOW
SUB SWITCH
(REAR: LH)
POWER
WINDOW
MOTOR
(REAR: LH)
POWER
WINDOW
SUB SWITCH
(REAR: RH)
POWER
WINDOW
MOTOR
(REAR: RH)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
CPU
CPU
Power Window (rear) Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-96
• Malfunction of the front power window regulator
motor (RH) <LH drive vehicles>, front power win-
dow regulator motor (LH) <RH drive vehicles>,
power window regulator motor (rear: RH) or
power window regulator motor (rear: LH)
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
Step 1. Check the power window main switch.
Check that the power window lock switch is turned
off.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Turn off the power window lock switch.
Step 2. Determine a trouble spot.
Q: Which power window does not work?
Front passenger's door <LH drive vehicles> :
Go
to Step 3.
Front passenger's door <RH drive vehicles> :
Go
to Step 12.
Rear right door :
Go to Step 21.
Rear left door :
Go to Step 30.
Step 3. Connector check: E-14 power window
sub switch (front) connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the connector.
Step 4. Resistance measurement at E-14 power
window sub switch (front) connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Resistance between E-14 power window sub
switch (front) connector terminal 1 and body
earth
OK: 2
Ω or less
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Go to Step 5.
AC310488
Connector: E-14 <LHD>
Harness side
AD
Front door (RH)
AC310488
Connector: E-14 <LHD>
Harness side
AD
Front door (RH)
AC303981
Connector E-14
(Harness side)
AC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-97
Step 5. Check the wiring harness from E-14
power window sub switch (front) connector
terminal No.1 to body earth.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connector C-110, and repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 6. Voltage measurement at E-14 power
window sub switch (front) connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Turn the ignition switch to the ON position.
(3) Voltage between E-14 power window sub switch
(front) connector terminal 4 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Go to Step 7.
Step 7. Connector check: C-224 power window
relay connector
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the connector.
AC310488
Connector: E-14 <LHD>
Harness side
AD
Front door (RH)
AC310452
Connector: C-110 <LHD>
AC
AC310488
Connector: E-14 <LHD>
Harness side
AD
Front door (RH)
AC303982
Connector E-14
(Harness side)
AC
AC310448
AI
Connector: C-224 <LHD>
Junction block (front view)
Junction block side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-98
Step 8. Check the wiring harness from E-14
power window sub switch (front) connector
terminal No.4 to C-224 power window relay
connector terminal No.4.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connectors C-110 and junction block connector
C-211, and repair if necessary.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 9. Connector check: E-11 front power
window regulator motor (RH) connector
Q: Is the check result normal?
YES :
Go to Step 10.
NO :
Repair the connector.
Step 10. Check the wiring harness from E-11
front power window regulator motor (RH)
connector terminal Nos.1 and 4 to E-14 front
power window sub switch (RH) connector
terminal Nos.5 and 7.
• Check the input and output lines for open or short
circuit.
AC310449
AD
Connectors: C-211, C-224 <LHD>
Junction block (front view)
Junction block side
C-211
C-224
C-224
Harness side
C-211
AC310488
Connector: E-14 <LHD>
Harness side
AD
Front door (RH)
AC310452
Connector: C-110 <LHD>
AC
AC310488
Connector: E-11 <LHD>
Harness side
E-11 (GR)
AE
Front door (RH)
AC310489
Connectors: E-11, E-14 <LHD>
E-14
E-11
Harness side
Harness side
E-14
E-11 (GR)
AB
Front door (RH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст