Mitsubishi Lancer Evolution IX. Manual — part 371

ACX00571

M.U.T.-II connected

Within 10 seconds

Hazard
warning
switch

ON

OFF

1

2

3

4

5

6

AB

KEYLESS ENTRY SYSTEM

BODY

42-45

4. Press the hazard warning switch six times within

10 seconds.
NOTE: Once the process is completed six times,
then it will operate with all doors lock and unlock
operations once and then go to the save mode.
NOTE: The hazard warning lamp switch is turned
on and off alternately whenever it is pushed.

5. Press the transmitter switch, and then press it two

times within 10 seconds of the first press. This will
register the code.

6. Once the program is saved, it will operate once

with the all doors lock and unlock operations.

7. If you are using two or more transmitters or have

added a second transmitter, the next transmitter
should be registered within one minute after
registering the code for the previous transmitter.
The registration procedure is common for all the
transmitters.

8. Registration mode will be cancelled under the

following conditions:

• When the secret code for four transmitters has

been registered;

• When passing one minute after finishing the reg-

istration of all transmitters;

• When the M.U.T.-II is disconnected from the diag-

nosis connector;

• When the key is removed from the key cylinder;

• When no secret codes have been registered for

more then one minute after the registration mode
is entered;

9. After the registration is completed, remove the

ignition key and close all the doors, and then
check that the keyless entry system operates
normally.

WHEN THE SPECIAL TOOL V.C.I.
(MB991824) IS USED

1. Check that the doors lock normally when the key

is used.

2. Insert the ignition key.

CAUTION

Before connecting or disconnecting the V.C.I.,
turn the ignition switch to the "LOCK" (OFF)
position.

AC309970

AC211686

AC

MB991911

MB991824

16-Pin

3. Connect the V.C.I. to the diagnosis connector.

ACX00571

Within 10 seconds

Hazard
warning
lamp
switch

ON

OFF

1

2

3

4

5

6

AQ

V.C.I. connected

4. Press the hazard warning lamp switch six times

within 10 seconds.
NOTE: Once the process is completed six times,
then it will operate with all doors lock and unlock
operations once and then go to the save mode.
NOTE: The hazard warning lamp switch is turned
on and off alternately whenever it is pushed.

5. Press the transmitter switch, and then press it two

times within 10 seconds of the first press. This will
register the code.

6. Once the program is saved, it will operate once

with the all doors lock and unlock operations.

KEYLESS ENTRY SYSTEM

BODY

42-46

7. If you are using two or more transmitters or have

added a second transmitter, the next transmitter
should be registered within one minute after
registering the code for the previous transmitter.
The registration procedure is common for all the
transmitters.

8. Registration mode will be cancelled under the

following conditions:

• When the secret code for four transmitters has

been registered;

• When passing one minute after finishing the reg-

istration of all transmitters;

• When the V.C.I. is disconnected from the diagno-

sis connector;

• When the key is removed from the key cylinder;

• When no secret codes have been registered for

more then one minute after the registration mode
is entered;

9. After the registration is completed, remove the

ignition key and close all the doors, and then
check that the keyless entry system operates
normally.

TRANSMITTER

TRANSMITTER

M1428002800086

DISASSEMBLY SERVICE POINT
BATTERY REMOVAL

CAUTION

Do not allow water or dust to enter the inside of
the transmitter when it is open. Also, do not
touch the precision electronic device.

AC303199

AC304118

AC304142AB

Master key

Master key side

Case

Case side

Battery

Transmitter assembly

Transmitter assembly

Since the battery is incorporated into the transmitter
assembly, disassemble the transmitter assembly to
remove the battery.

KEYLESS ENTRY SYSTEM

BODY

42-47

ASSEMBLY SERVICE POINT
BATTERY INSTALLATION

CAUTION

Do not allow water or dust to enter the inside of
the transmitter when it is open. Also, do not
touch the precision electronic device.

AC303199

AC304118

AC304142AD

-

(+)

Master key side

Case side

Battery

Transmitter assembly

Master key

Case

Transmitter assembly

(–)

1. Install a new battery to the transmitter assembly

with its (+) side facing towards the case side.

Battery required for replacement: Coin type
battery CR1616

2. Check the transmitter operation.

INSPECTION

M1428003800067

TRANSMITTER BATTERY CHECK

AC004486

Measure the voltage of the battery. If the voltage of
the battery is not within the standard value, replace
the battery.

Standard value: 2.5

− 3.2 V

NOTES