Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 551
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-11
CR O SSM EM B ER
REMOVAL AND INSTALLATION
M1321003200089
CAUTION
•
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle
on the ground in the unladen condition.
•
For vehicles with SRS, before removal of steering gear box, refer to GROUP 52B, center the front
wheels and remove the ignition key. Failure to do so may damage the SRS clock spring and render
the SRS system inoperative, risking serious injury.
Pre-removal Operation
•
Power Steering Fluid Draining (Refer to GROUP 37A, On-
vehicle Service
−
Fluid Replacement
.)
•
Centermember Removal (Refer to
•
Front Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust pipe and Main Muffler
<2.4L Engine>,
<3.0L Engine>.)
•
Stabilizer Bar Removal (Refer to GROUP 33A, Stabilizer
Bar
•
Rear Roll Stopper Removal (Refer to
Post-installation Operation
•
Rear Roll Stopper Installation (Refer to
•
Stabilizer Bar Installation (Refer to GROUP 33A, Stabi-
lizer Bar
.)
•
Front Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
<2.4L Engine>,
<3.0L Engine>.)
•
Centermember Installation (Refer to
.)
•
Power Steering Fluid Supplying and Bleeding (Refer to
GROUP 37A, On-vehicle Service
−
Fluid Replacement
•
Steering Wheel Straight Ahead Position Checking.)
•
Wheel Alignment Check and Adjustment (Refer to
GROUP 33A, On-vehicle Service
−
Front Wheel Align-
ment Check and Adjustment
.)
AC005142
6
7
8
9
10
4
11
5
4
2
1
108 ± 10 N·m
80 ± 7 ft-lb
108 ± 10 N·m*
80 ± 7 ft-lb*
88 ± 10 N·m
65 ± 7 ft-lb
74 ± 4 N·m
55 ± 3 ft-lb
81 ± 12 N·m
60 ± 9 ft-lb
AB
3
REMOVAL STEPS
1.
STAY <2.4L ENGINE>
2.
LOWER ARM AND
CROSSMEMBER CONNECTION
3.
LOWER ARM MOUNT BOLT
•
POWER STEERING GEAR BOX
(REFER TO GROUP 37A,
POWER STEERING GEAR BOX
.)
REMOVAL STEPS (Continued)
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-12
Required Special Tools:
•
MB990828: Bushing Remover and Installer
•
MB991045: Bushing Remover and Installer
CROSSMEMBER BUSHING REPLACEMENT
M1321000900034
Crossmember Bushings A and B
1. Apply soapy water to the contact surface of the bushing
when press-fitted the bushing.
2. The bushing should be press-fitted so that the inner pipe
projection is at the standard length.
Standard values
••••
<2.4L ENGINE>
••••
Bushing A: 9.0
±
1.0 mm (0.35
±
0.04 inch)
••••
Bushing B: 4.0
±
1.0 mm (0.16
±
0.04 inch)
••••
<3.0L ENGINE>
••••
Bushing A, B: 9.0
±
1.0 mm (0.35
±
0.04 inch)
4.
CROSSMEMBER MOUNTING
NUT
5.
LOWER PLATE
6.
CROSSMEMBER
7.
STOPPER A
8.
STOPPER B
9.
BUSHING C
10. BUSHING A
11. BUSHING B
REMOVAL STEPS (Continued)
AC000306
REMOVAL
PRESS-FITTING
BOLT
WASHER
NUT
BASE
BASE
NUT
WASHER
BOLT
MB991045
AB
AC000307AB
<2.4L ENGINE>
BUSHING A
BUSHING B
INNER PIPE
INNER PIPE
AC000308
INNER PIPE
INNER PIPE
BUSHING A
BUSHING B
<3.0L ENGINE>
AB
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-13
Crossmember Bushing C
1. Use special tool MB990828 to drive out and press-fit the
crossmember bushing C.
2. The bushing should be press-fitted so that the inner pipe
projection is at the standard length.
Standard value (A): 4.0
±
0.5 mm (0.16
±
0.02 inch)
AC000309AB
REMOVAL
PRESS-FITTING
MB990828
AC000310
INNER PIPE
A
AB
SPECIFICATIONS
TSB Revision
POWER PLANT MOUNT
32-14
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATION
M1321004100085
SERVICE SPECIFICATION
M1321000300043
ITEMS
SPECIFICATIONS
Centermember front mounting bolt
93
±
15 N
⋅
m (69
±
11 ft-lb)
Centermember rear mounting bolt
74
±
4 N
⋅
m (55
±
3 ft-lb)
Crossmember and stay connecting bolt <2.4L ENGINE>
74
±
4 N
⋅
m (55
±
3 ft-lb)
Crossmember mounting bolt
108
±
10 N
⋅
m (80
±
7 ft-lb)
Crossmember mounting nut
88
±
10 N
⋅
m (65
±
7 ft-lb)
Dynamic damper bolt
4.9
±
1.0 N
⋅
m (44
±
8 in-lb)
Engine mount bracket bolt
86
±
12 N
⋅
m (64
±
8 ft-lb)
Engine mount bracket nut
86
±
12 N
⋅
m (64
±
8 ft-lb)
Engine mount insulator mounting bolt
81
±
12 N
⋅
m (60
±
9 ft-lb)
Engine mount stay bolt <3.0L ENGINE>
35
±
5 N
⋅
m (26
±
4 ft-lb)
Lower arm and crossmember connecting nut
108
±
10 N
⋅
m (80
±
7 ft-lb)
Lower arm mount bolt
81
±
12 N
⋅
m (60
±
9 ft-lb)
Transaxle and front roll stopper connecting bolt
45
±
5 N
⋅
m (34
±
3 ft-lb)
Transaxle and front roll stopper connecting nut
45
±
5 N
⋅
m (34
±
3 ft-lb)
Transaxle and rear roll stopper connecting bolt
45
±
5 N
⋅
m (34
±
3 ft-lb)
Transaxle and rear roll stopper connecting nut
45
±
5 N
⋅
m (34
±
3 ft-lb)
Transaxle mount bracket nut
57
±
7 N
⋅
m (42
±
5 ft-lb)
Transaxle mount insulator mounting nut
81
±
12 N
⋅
m (60
±
9 ft-lb)
ITEMS
STANDARD VALUE
Inner pipe projection mm (in)
Bushing A
9.0
±
1.0 (0.35
±
0.04)
Bushing B
2.4L ENGINE
4.0
±
1.0 (0.16
±
0.04)
3.0L ENGINE
9.0
±
1.0 (0.35
±
0.04)
Bushing C
4.0
±
0.5 (0.16
±
0.02)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст