Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 102
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-107
STEP 8. Check the throttle position sensor.
(1) Disconnect the connector B-07.
(2) Measure the resistance between throttle position sensor
side connector terminal 1 and 4.
Standard value: 3.5
−
6.5 k
Ω
(3) Measure resistance between the throttle position sensor
side connector terminal 1 and 3.
(4) Move the throttle valve from the idle position to the full-open
position.
•
Resistance should change smoothly in proportion to the
opening angle of the throttle valve.
Q: Is the resistance normal?
YES : Go to Step 9.
NO : Replace the throttle position sensor.(Refer to
, Throttle Body.) Then go to Step 11.
STEP 9. Check connector C-60 at ECM <M/T> or connector
C-54, C-57 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
ACX02472
CONNECTOR : B-07
THROTTLE
POSITION
SENSOR
AE
AK000320
1 2 3 4
THROTTLE POSITION
SENSOR SIDE
CONNECTOR
AB
AK000280
C-54
C-60
ECM<M/T>
OR
PCM<A/T>
CONNECTORS:C-60<M/T>,C-54,C-57<A/T>
BD
C-57
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-108
STEP 10. Using scan tool MB991502, check data list item
14: Throttle Position Sensor.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991502 to the data reading mode for item
14, Throttle Position Sensor.
•
With the throttle valve in the idle position, voltage should
be between 0.535 and 0.735 volts.
•
With the throttle valve in the full-open position, voltage
should be between 4.5 and 5.5 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points (
NO : Replace the ECM or PCM. Then go to Step 11.
STEP 11. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to,
Procedure 6
−
Other Monitor (
).
(2) Check the diagnostic trouble code (DTC).
Q: Is the DTC P0123 is output?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0128: Coolant Thermostat Malfunction
TECHNICAL DESCRIPTION
•
The ECM <M/T> or PCM <A/T> checks the time
for the engine coolant temperature to reach the
judgment temperature.
DTC SET CONDITIONS
Check Conditions
•
Engine coolant temperature is between -10
°
C
(14
°
F) and 82
°
C (180
°
F) when the engine is
started.
•
The engine coolant temperature
−
intake air
temperature is 5
°
C (48
°
F) or less when the
engine is started.
•
The intake air temperature when the engine is
started
−
intake air temperature is 2
°
C (36
°
F) or
less.
•
The volume air flow sensors output frequency is
in the low frequency (50-100Hz or less) state for
400 seconds or less.
Judgment Criteria
•
The time for the engine coolant temperature to
rise to 82
°
C (180
°
F) takes longer than the
specified time *.
*: Approximately 11 to 23 minutes when the
engine coolant temperature at start is 20
°
C
(68
°
F) or more.
Approximately 12 to 60 minutes when the engine
coolant temperature at start is 20
°
C (68
°
F)
or less.
•
Only one monitor during one drive cycle.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
•
The thermostat is faulty
•
ECU failed. <M/T>
•
PCM failed. <A/T>
AKX01177
16 PIN
MB991502
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-109
DIAGNOSIS
STEP 1. Check the cooling system.
Refer to GROUP 14, Engine Cooling Diagnosis
.
Q: Is the cooling system normal?
YES : Replace the ECM or PCM. Then check that the DTC
P0128 does not reset.
NO : Repair it. Then check that the DTC P0128 does not
reset.
DTC P0130: O
2
Sensor Circuit Malfunction (sensor 1)
AK000657
4
1 2
3
BL
ACK
BL
ACK
WHITE
B-17
MU802605
ENGINE CONTROL
MODULE(ECM)<M/T>
OR
POWERTRAIN CONTROL
MODULE(PCM)<A/T>
HEATED OXYGEN
SENSOR(FRONT)
FROM MFI RELAY
TO ECM
OR PCM
1
2
3
4
92<M/T>
57<A/T>*1
76<M/T>
71<A/T>*2
C-60<M/T>
(MU803772)
C-54<A/T>
(MU803781)
C-57<A/T>
(MU803782)
NOTE
*1:PCM connector C-54<A/T>
*2:PCM connector C-57<A/T>
98
78
71
88 89
76 77
72
79
91
73
80
74
75
81
92
8283
93
8485
94
8687
9596
90
97
82
78
81
80
89 90 91 92
79
87
71
74
73
72
76
75
77
85
88
83 84
86
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58 59
60 61 62 63
64 65 66
47
41
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-110
CIRCUIT OPERATION
•
A voltage corresponding to the oxygen
concentration in the exhaust gas is sent to the
ECM (terminal 76) <M/T> or PCM (terminal 71)
<A/T> from the output terminal (terminal 4) of the
heated oxygen sensor (front).
•
Terminal 2 of the heated oxygen sensor (front) is
grounded with ECM (terminal 92) <M/T> or PCM
(terminal 57) <A/T>.
TECHNICAL DESCRIPTION
•
The heated oxygen sensor (front) detects the
concentration of oxygen in the exhaust gas; it
converts those data to voltage, and inputs the
resulting signals to the ECM <M/T> or PCM <A/
T>.
•
When the heated oxygen sensor (front) begins to
deteriorate, the heated oxygen sensor signal
response becomes poor.
•
The ECM <M/T> or PCM <A/T> forcibly varies
the air/fuel mixture to make it leaner and richer,
and checks the response speed of the heated
oxygen sensor (front). In addition, the ECM <M/
T> or PCM <A/T> also checks for an open circuit
in the heated oxygen sensor (front) output line.
DTC SET CONDITIONS
Check Conditions
•
Heated oxygen sensor (front) signal voltage has
continued to be 0.2 volt or lower for three minutes
or more after the starting sequence was
completed.
•
Engine coolant temperature is higher than 82
°
C
(180
°
F).
•
Engine speed is higher than 1,200 r/min.
•
Volumetric efficiency is higher than 25 percent.
•
Monitoring time: 7 seconds.
Judgment Criteria
•
Input voltage supplied to the ECM <M/T> or PCM
<A/T> interface circuit is higher than 4.5 volts
when 5 volts is applied to the heated oxygen
sensor (front) output line via a resistor.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
•
Heated oxygen sensor (front) deteriorated.
•
Open circuit in heated oxygen sensor (front)
output line.
•
Open circuit in heated oxygen sensor (front)
ground line.
•
ECM failed. <M/T>
•
PCM failed. <A/T>
DIAGNOSIS
Required Special Tools
MB991502: Scan Tool (MUT-II)
MD998464: Test Harness
ACX02476
CONNECTOR : B-17
HEATED OXYGEN
SENSOR (FRONT)
AD
AK000280
C-54
C-60
ECM<M/T>
OR
PCM<A/T>
CONNECTORS:C-60<M/T>,C-54,C-57<A/T>
BD
C-57
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст