Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 278
![](/vehicles/winoney/isene/butrele/utowos.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-311
STEP 9. Check the output voltage at fuel tank differential
pressure sensor connector D-18.
(1) Disconnect fuel tank differential pressure sensor connector
D-18.
(2) Use special tool (MB991658) to connect terminals 2 and 3
of the disconnected sensor connector and those of the
harness side connector, respectively.
(3) Turn the ignition switch to the "ON" position.
(4) Remove the fuel cap.
(5) Measure the voltage between terminal 1 and ground by
backprobing.
•
Voltage should be between 2.0 and 3.0 volts.
(6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading within the specified value?
YES : Check connectors D-16, C-90, C-28, C-62 <M/T> or
C-59 <A/T> and repair or replace as required. Refer
to GROUP 00E, Harness Connector Inspection
. If connectors D-16, C-90, C-28, C-62 <M/T>
or C-59 <A/T> are in good condition, check the
harness between fuel tank differential pressure
sensor connector D-18 and ECM connector C-62 <M/
T> or PCM connector C-59 <A/T> for short circuit to
ground, then repair if necessary. Then go to Step 26.
NO : Replace the fuel tank differential pressure sensor.
Then go to Step 26.
STEP 10. Check the output circuit voltage at ECM
connector C-62 <M/T> or PCM connector C-59 <A/T>.
(1) Do not disconnect the ECM connector C-62 <M/T> or PCM
connector C-59 <A/T>.
(2) Turn the ignition switch to the "ON" position.
(3) Remove the fuel cap.
(4) Measure the voltage between terminal 93 <M/T> or terminal
92 <A/T> and ground by backprobing.
•
Voltage should be between 2.0 and 3.0 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading within the specified value?
YES : Go to Step 18.
NO : Check connectors D-16, C-90, C-28, C-62 <M/T> or
C-59 <A/T> and repair or replace as required. Refer
to GROUP 00E, Harness Connector Inspection
. If connectors D-16, C-90, C-28, C-62 <M/T>
or C-59 <A/T> are in good condition, check the
harness between intermediate connector D-16 and
ECM connector C-62 <M/T> or PCM connector C-59
<A/T> for open circuit or damage. Then repair if
necessary. Then go to Step 26.
ACX01760AB
MB991658
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
AC002082
HARNESS SIDE
CONNECTOR
<A/T>
C-59
<M/T>
C-62
AC
![](/vehicles/winoney/isene/butrele/pocardoungs.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-312
STEP 11. Check the 5-volt supply circuit voltage at ECM
connector C-58 <M/T> or PCM connector C-55 <A/T>.
(1) Do not disconnect ECM connector C-58 <M/T> or PCM
connector C-55 <A/T>.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 42 <M/T> or terminal
46 <A/T> and ground by backprobing.
•
Voltage should be between 4.8 and 5.2 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading within the specified value?
YES : Check connectors D-16, C-90, C-28, C-58 <M/T> or
C-55 <A/T> and repair or replace as required. Refer
to GROUP00E, Harness Connector Inspection
. If connectors D-16, C-90, C-28, C-58 <M/T>
or C-55 <A/T> are in good condition, check the
harness between intermediate connector D-16 and
ECM connector C-58 <M/T> or PCM connector C-55
<A/T> for open circuit or damage. Then repair if
necessary. Then go to Step 26.
NO : Go to Step 12.
STEP 12. Check ECM connector C-58 <M/T> or PCM
connector C-55 <A/T> for damage.
(1) Disconnect ECM connector C-58 <M/T> or PCM connector
C-55 <A/T>.
Q: Is there any failure at ECM connector C-58 <M/T> or
PCM connector C-55 <A/T>?
YES : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
NO : Go to Step 13.
STEP 13. Check the sensor power supply line for short
circuit to ground at ECM connector C-58 <M/T> or PCM
connector C-55 <A/T>.
(1) Disconnect ECM connector C-58 <M/T> or PCM connector
C-55 <A/T> and measure at the harness side.
(2) Check for the continuity between terminal 42 <M/T> or
terminal 46 <A/T> and ground.
•
There should be 2 ohms or more.
Q: Does the multi-meter reading exceed the specified
value?
YES : Replace ECM or PCM. Then go to Step 26.
NO : Go to Step 14.
AC002083AC
HARNESS SIDE
CONNECTOR
<M/T> C-58
<A/T> C-55
AC001689
CONNECTOR: C-58 <M/T>, C-55 <A/T>
ECM <M/T>
OR
PCM <A/T>
C-58
<M/T>
C-55
<A/T>
AO
AC002084 AC
<M/T> C-58
<A/T> C-55
HARNESS SIDE
CONNECTOR
![](/vehicles/winoney/isene/butrele/tro.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-313
STEP 14. Check the sensor power supply lines.
(1) Check all the sensor power supply lines for damage, which
flow through the harness ECM connector (terminal 42) <M/
T> or PCM connector (terminal 46) <A/T>.
Q: Is there any failure in the sensor power supply lines?
When a failure is found : Repair if necessary. (Refer to
GROUP 90, Circuit Diagrams
−
MFI System <M/T>
STEP 15. Check the ground circuit voltage at ECM
connector C-58 <M/T> or PCM connector C-55 <A/T>.
(1) Do not disconnect ECM connector C-58 <M/T> or PCM
connector C-55 <A/T>.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 49 <M/T> or 57 <A/
T> and ground by backprobing.
•
Voltage should be 0.5 volts or less.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading below the specified value?
YES : Check connectors D-16, C-90, C-28, C-58 <M/T> or
C-55 <A/T> and repair or replace as required. Refer
to GROUP 00E, Harness Connector Inspection
. If connectors D-16, C-90, C-28, C-58 <M/T>
or C-55 <A/T> are in good condition, check the
harness between intermediate connector D-16 and
ECM connector C-58 <M/T> or PCM connector C-55
<A/T> for open circuit or damage. Then repair if
necessary. Then go to Step 26.
NO : Go to Step 16.
STEP 16. Check ECM connector C-58 <M/T> or PCM
connector C-55 <A/T> for damage.
(1) Disconnect ECM connector C-58 <M/T> or PCM connector
C-55 <A/T>.
Q: Is there any failure at ECM connector C-58 <M/T> or
PCM connector C-55 <A/T>?
YES : Replace ECM or PCM. Then go to Step 26.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
AC002085
HARNESS SIDE
CONNECTOR
<M/T> C-58
<A/T> C-55
AC
AC001689
CONNECTOR: C-58 <M/T>, C-55 <A/T>
ECM <M/T>
OR
PCM <A/T>
C-58
<M/T>
C-55
<A/T>
AO
![](/vehicles/winoney/isene/butrele/eve.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-314
STEP 17. Check the harness between fuel tank differential
pressure sensor connector D-18 and intermediate
connector D-16 for open circuit or damage.
(1) Disconnect fuel tank differential pressure sensor connector
D-18 and intermediate connector D-16.
Q: Is there any failure between fuel tank differential
pressure sensor connector D-18 and intermediate
connector D-16?
YES : Repair it. Then go to Step 26.
NO : Check connectors D-18, D-16 and repair or replace
as required. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
STEP 18. Check ECM connector C-62 <M/T> or PCM
connector C-59 <A/T> for damage.
(1) Disconnect ECM connector C-62 <M/T> or PCM connector
C-59 <A/T>.
Q: Is there any failure at ECM connector C-62 <M/T> or
PCM connector C-59 <A/T>?
YES : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
NO : Go to Step 19.
AC002041AB
CONNECTOR: D-18
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
AC002549 AB
CONNECTOR: D-16
INTERMEDIATE
CONNECTOR
AC001689
CONNECTOR: C-62<M/T>, C-59 <A/T>
ECM <M/T>
OR
PCM <A/T>
C-62
<M/T>
C-59
<A/T>
AP
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст