Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 634
DOOR
TSB Revision
BODY
42-83
WINDOW GLASS RUNCHANNEL AND DOOR OPENING WEATHERSTRIP
REMOVAL AND INSTALLATION
M1423003100063
AC003394
1
5
2
1
2
6
7
<ECLIPSE SPYDER>
A
DOOR OUTER OPENING WEATHER-
STRIP REMOVAL STEPS
•
DOOR TRIM (REFER TO
•
DOOR DELTA SASH (REFER TO
.)
1. BELT LINE MOULDING
<<A>> >>A<<
2. DOOR OUTER OPENING WEATH-
ERSTRIP
DRIP LINE WEATHERSTRIP REMOVAL
STEPS
3. DRIP LINE WEATHERSTRIP
4. DRIP LINE WEATHERSTRIP
HOLDER
DOOR INNER OPENING WEATHER-
STRIP REMOVAL STEPS
•
SCUFF PLATE (REFER TO GROUP
52A
.)
5. DOOR INNER OPENING WEATHER-
STRIP
6. DOOR INNER FRONT OPENING
WEATHERSTRIP
7. DOOR INNER REAR OPENING
WEATHERSTRIP
DOOR
TSB Revision
BODY
42-84
CLIP AND CLAW POSITIONS
REMOVAL SERVICE POINT
<<A>> DOOR OUTER OPENING WEATHERSTRIP
REMOVAL
Make a tool as shown and remove the door opening
weatherstrip.
AC002008
: SECTIONAL VIEW
OF CLIP POSITION
: SECTIONAL VIEW
OF CLIP POSITION
AC
<ECIPSE>
ACX00555
15 mm (0.6 in)
8 mm
(0.3 in)
AB
4 mm (0.2 in)
THICKNESS:
1 mm (0.04 in)
FABRICATED TOOL
DOOR
TSB Revision
BODY
42-85
INSTALLATION SERVICE POINT
>>A<< DOOR OUTER OPENING WEATHERSTRIP
INSTALLATION
The clip color identifies the left and right weatherstrips.
INSPECTION
M1429001400077
POWER WINDOW RELAY CONTINUITY CHECK
POWER WINDOW MOTOR CHECK
1. Connect a battery directly to the motor terminals and check
that the motor runs smoothly.
2. Check that the motor runs in the opposite direction when the
battery is connected with the polarity reversed.
3. If defect is found, replace the window regulator as an
assembly.
APPLICABLE SIDE
IDENTIFICATION COLOR
Left door
Natural (White)
Right door
Orange
BATTERY
VOLTAGE
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
1
−
3Continuity
1-Battery (-)
terminal,3-battery
(+)terminal
4
−
5
Continuity
1
2 3
4
5
1
3
4
5
ACX01544
AC003899
AC003005
AB
POWER WINDOW
RELAY
FRONT HARNESS
RELAY BOX
2
1
AC003900 AB
SLIDER
LIFTGATE
TSB Revision
BODY
42-86
LIFTG ATE
LIFTGATE DIAGNOSIS
INTRODUCTION TO LIFTGATE DIAGNOSIS
M1424002500050
Difficult locking and unlocking and uneven clearance,
and generation of wind noise from the liftgate may be
improper adjustment of the liftgate.
LIFTGATE DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1424002600057
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
liftgate fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1424002700054
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Difficult locking and unlocking
DIAGNOSIS
STEP 1. Check the release cable routing
condition.
Q: Is the release cable routing condition good?
YES :
Go to Step 3.
NO :
Repair it, then go to Step 2.
STEP 2. Check the engagement of the liftgate
latch and liftgate striker.
Q: Are the liftgate latch and liftgate striker engaged
correctly?
YES :
Adjust it. Refer to
NO :
Then go to Step 3.
STEP 3. Check symptoms.
Q: Does the liftgate lock operate easily?
YES :
This diagnosis is complete.
NO :
Return to Step 1.
INSPECTION PROCEDURE 2: Uneven body clearance
DIAGNOSIS
STEP 1. Check the liftgate installation condition.
Q: Is the liftgate installation in good condition?
YES :
Adjust it. Refer to
NO :
Then go to Step 2.
STEP 2. Check symptoms.
Q: Is the clearance with the body even?
YES :
This diagnosis is complete.
NO :
Return to Step 1.
SYMPTOMS
INSPECTION
PROCEDURE
REFERENCE PAGE
Difficult locking and unlocking
1
Uneven body clearance
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст