Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 632
DOOR
TSB Revision
BODY
42-75
INSTALLATION SERVICE POINTS
>>A<< POWER WINDOW MOTOR/WINDOW REGULATOR
ASSEMBLY INSTALLATION
1. Power window motor and window regulator assembly
installation procedure
CAUTION
Do not operate the power window motor until the glass
installation is finished.
(1) Connect the power window motor to the body-side
harness connector, and then turn on the ignition switch.
(2) Continue to pull the power window switch until the power
window motor stops.
NOTE: Power window motor stops automatically and the
limit switch incorporated in the power motor will be reset.
(3) Turn off the ignition switch, and then remove window
motor from the body-side harness connector.
(4) Align the power window motor drive shaft and the square
hole in the drum by the following procedure, while using
the guide and the opening in the motor housing as a
reference for the installation position.
a. Align the square hole with the drive shaft by sliding the
glass bracket (glass mounting section) or by turning
the drum using a ratchet wrench [with a socket
diameter of 12.7 mm (0.50 inches)].
b. Turn the drum to position the glass bracket as shown
in the illustration. Support the drum and the guide with
your hand while turning the drum, otherwise the wires
may pull out of the drum.
c. If the wires pull out of the drum, re-insert them by
following the drum and regulator wire installation
procedure.
AC000485
DRUM
GUIDE
SQARE
HOLE
GUIDE
DRIVESHAFT
AB
AC000486
GLASS BRACKET
RACHET WRENCH
AB
AC000487
GLASS
BRACKET
APPROXIMATELY
85 mm (3.3 in)
AB
DOOR
TSB Revision
BODY
42-76
(5) Align the guide and the opening of the motor housing,
and slide the guide into the motor housing while holding
the guide and drum.
CAUTION
Make sure that the metal cover is installed securely and
does not move, in order to stop the drum from vibrating. If
the drum vibrates, the glass may not slide up and down
smoothly, or it may fall down.
(6) install the metal cover securely to housing.
2. Drum and regulator wire installation procedure
(1) Place the drum, guide and regulator on a work bench as
shown in the illustration.
a. Place the drum so that the square hole is facing
upward.
b. Place the guide so that the slits are facing upward.
c. Place the regulator so that the glass bracket is facing
downward. Position the glass bracket so that glass is
in the fully-open position.
(2) Pass the springs over the wires, and then install the
lowering wire to the guide first, followed by the lifting wire.
(The lifting wire should be on top of the lowering wire.)
AC000488AB
AC000489
MOUNTING
SCREW
METAL COVER
AB
AC000490
GUIDE
DRUM
SQARE HOLE
SLIT
SPRING A
LIFTING
WIRE
LOWERING
WIRE
SPRING B
AB
AC000491
LOWERING
WIRE
LIFTING
WIRE
GUIDE
SLIT
SPRING
AB
DOOR
TSB Revision
BODY
42-77
(3) Use some narrow-gauge wire [approximately 0.5 mm
(0.02 inches) diameter] to compress the springs, and
then tie the narrow-gauge wire a to the slits in the guide.
(4) Insert the end of the lowering wire into the wire hole at
the bottom of the drum, and then wrap the bottom so that
there is no slackness in the wire.
(5) Install the lifting wire to the drum as following:
a. Insert the end of the lifting wire into the wire hole at the
top of the drum.
b. Raise the front of the drum until the drum is vertical,
and then position the lifting wire in the groove of the
drum.
AC000492
NARROW-
GAUGE
WIRE
AB
AC000493
SLIT
AB
AC000494
LOWERIING
AB
AC000495
LIFTING WIRE
AB
AC000496AB
DOOR
TSB Revision
BODY
42-78
c. Return the drum to its original position while holding
the wires to make sure that they do not pull out.
(6) After installing the power window motor assembly to the
window regulator assembly, cut and remove the wires
witch are compressing the springs.
3. Operation check
CAUTION
•
Do not operate the window regulator assembly before
installing the window glass, otherwise the limit switch
will be set.
•
Window glass safety mechanism does not operate
when the window glass is closed fully at first time.
(1) Install the window glass to the window regulator
assembly.
(2) Close the window glass completely.
NOTE: Closing the window glass completely will finish
the adjustment of the limit switch.
(3) Check that the limit switch operates correctly.
>>B<< DOOR WINDOW GLASS INSTALLATION
1. Temporarily secure the door window glass to the door
window regulator.
2. After raising the door window glass as far as it will go, fully
secure the door window glass to the door window regulator
assembly.
AC000497AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст