Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 374
![](/vehicles/winoney/isene/butrele/gand.png)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-15
STEP 5. Check the harness wire between auto-cruise
control vacuum pump connector A-01 and auto-cruise
control-ECU connector C-20.
Q: Is any harness wire between auto-cruise control
vacuum pump connector A-01 and auto-cruise control-
ECU connector C-20 damaged?
YES : Repair the harness wire and then check that
diagnostic trouble code 11 is not output.
NO : Check that diagnostic trouble code 11 is not output.
If diagnostic trouble code 11 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 11 is not
output.
AC001449
CONNECTOR: A-01
RESERVE
TANK
AB
AC001451
CONNECTOR: C-20
AB
![](/vehicles/winoney/isene/butrele/mough.png)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-16
DTC 12: Vehicle Speed Sensor System
AC005109
Vehicle Speed Sensor System Circuit
AB
![](/vehicles/winoney/isene/butrele/fasde.png)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-17
CIRCUIT OPERATION
This circuit checks the operation of the vehicle speed
sensor.
When the vehicle moves forward and reverses, the
sensor turns ON and OFF repeatedly.
DTC SET CONDITIONS
The vehicle speed signals from the vehicle speed
sensor are not input to the auto-cruise control-ECU
when the vehicle speed is 40 km/h (25 mph) or more.
TROUBLESHOOTING HINTS
The most likely causes for this code to be set are:
•
Malfunction of the vehicle speed sensor.
•
Damaged harness or connector.
•
Malfunction of the auto-cruise control-ECU.
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
AC003550 AC
CONNECTORS: B-36, B-39 <2.4 L>
B-36 <M/T>
B-39 <M/T>
B-39 <A/T>
AC003599 AB
CONNECTOR: C-28
AC003553 AI
CONNECTOR: C-78
AC001451
CONNECTOR: C-20
AB
AC003553 AH
CONNECTOR: C-77
![](/vehicles/winoney/isene/butrele/udeaith.png)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-18
STEP 1. Check the speedometer.
Q: Does the speedometer work normally?
YES : Go to Step 2.
NO : Check the speedometer circuit and repair or replace
as required.
(Refer to GROUP 54A, Combination Meter Assembly
and Vehicle Speed Sensor
STEP 2. Check joint connector (1) C-77.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 12 is not
output.
NO : Go to Step 3.
STEP 3. Check the harness wire between auto-cruise
control-ECU connector C-20 and joint connector (1) C-77.
Q: Is any harness wire between auto-cruise control-ECU
connector C-20 and joint connector (1) C-77 damaged?
YES : Repair the harness wire and then check that
diagnostic trouble code 12 is not output.
NO : Check that diagnostic trouble code 12 is not output.
If diagnostic trouble code 12 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 12 is not
output.
AC003553 AH
CONNECTOR: C-77
AC001451
CONNECTOR: C-20
AB
AC003553 AH
CONNECTOR: C-77
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст