Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 484
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-228
STEP 11. Replace the output shaft speed sensor.
(1) Replace the output shaft speed sensor. Refer to GROUP
23B, Transaxle
(2) Carry out a test drive.
(3) Read in the A/T diagnostic trouble code (DTC).
Q: Is the A/T diagnostic trouble code output?
YES : Go to Step 12.
NO : The inspection is complete.
STEP 12. Replace the transfer drive gear or driven gear.
(1) Replace the output shaft. Refer to GROUP 23B, Transaxle,
Output Shaft
(2) Carry out a test drive.
(3) Read in the A/T diagnostic trouble code.
Q: Is the A/T diagnostic trouble code output?
YES : The A/T diagnostic trouble code may have set due to
external radio frequency (RFI), possibly caused by
cellular phone activity, after market components
installed on the vehicle, etc.
NO : The inspection is complete.
STEP 13. Replace the valve body.
(1) Replace the valve body. Refer to GROUP 23B, Transaxle
.
(2) Carry out a test drive.
(3) Read in the A/T diagnostic trouble code.
Q: Is the A/T diagnostic trouble code output?
YES : Go to Step 14.
NO : The inspection is complete.
STEP 14. Replace the PCM.
(1) Replace the PCM.
(2) Carry out a test drive.
(3) Read in the diagnostic trouble code.
Q: Is the A/T diagnostic trouble code output?
YES : Go to Step 15.
NO : The inspection is complete.
AC001837AD
OUTPUT SHAFT
SPEED SENSOR
AC002221AC
TRANSFER
DRIVE GEAR
TRANSFER
DRIVEN GEAR
AC001860 AB
VALVE
BODY
ASSEMBLY
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-229
STEP 15. Overhaul the A/T.
(1) Replace the following parts.
•
Replace the underdrive clutch. Refer to GROUP 23B,
Underdrive Clutch
. (When the codes of No.41,
No.42, No.43 are output individually or in plural.)
•
Replace the overdrive clutch. Refer to GROUP 23B,
Reverse and Overdrive Clutches
. (When the
codes of No.43, No.44 are output individually or in
plural.)
•
Replace the reverse clutch. Refer to GROUP 23B,
Reverse and Overdrive Clutches
. (When the
code of No.46 is output.)
•
Replace the low-reverse brake. Refer to GROUP 23B,
Transaxle
. (When the codes of No.41 and
No.46 are output.)
•
Replace the second brake. Refer to GROUP 23B,
Transaxle
. (When the codes of No.42 and
No.44 are output.)
•
Replace the one-way clutch (OWC-L). Refer to GROUP
23B, Low Reverse Annulus Gear
. (When the
code of No.41 is output individually.)
(2) Carry out a test drive.
(3) Read in the A/T diagnostic trouble code.
Q: Is the A/T diagnostic trouble code output again?
YES : The A/T diagnostic trouble code may have set due to
external radio frequency (RFI), possibly caused by
cellular phone activity, after market components
installed on the vehicle, etc.
NO : The inspection is complete.
DTC 52: Torque Coverter Clutch System
DTC SET CONDITIONS
If input shaft speed sensor is abnormal and drive
duty rate for the torque converter clutch solenoid
valve is 100 percent for continuous period of 4
seconds or more, it is judged that there is an
abnormality in the torque converter clutch system
and diagnostic trouble code number "52" is output.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set:)
•
Malfunction of the torque converter clutch
solenoid valve
•
Damaged harness, connector
•
Malfunction of the PCM
•
Malfunction of the underdrive clutch
DIAGNOSIS
Required Special Tool:
MB991502: Scan Tool (MUT-II)
AC001868
REVERSE
CLUTCH
SECOND
BRAKE
LOW-
REVERSE
BRAKE
UNDERDRIVE
CLUTCH
OVERDRIVE CLUTCH
AB
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-230
STEP 1. Using scan tool MB991502, read the A/T
diagnostic trouble code.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Read the A/T diagnostic trouble code.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is A/T diagnostic trouble code number "22" output?
, code number 22: Input Shaft
Speed Sensor System.
NO : Go to Step 2.
STEP 2. Using scan tool MB991502, check actuator test
item 06: Torque Converter Clutch Solenoid Valve.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Set scan tool MB991502 to actuator test mode for item 06:
Torque Converter Clutch Solenoid Valve.
•
An operation sound should be heard from solenoid
valve when the torque converter clutch solenoid valve is
operated.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : Go to Step 3..
NO : Replace the torque converter clutch solenoid valve.
Refer to GROUP 23B, Valve Body
AC001252
MB991502
16 PIN
AB
AC001252
MB991502
16 PIN
AB
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-231
STEP 3. Using the oscilloscope, check the waveform at
PCM connectors C-54 <2.4L Engine> or C-55 <3.0L
Engine> and C-61 <2.4L Engine> or C-63 <3.0L Engine> by
backprobing.
(1) Do not disconnect connectors C-54 <2.4L Engine> or C-55
<3.0L Engine> and C-61 <2.4L Engine> or C-63 <3.0L
Engine>.
(2) Connect an oscilloscope probe to PCM connector C-54
<2.4L Engine> or C-55 <3.0L Engine> terminal 57 and to
PCM connector C-61 <2.4L Engine> or C-63 <3.0L Engine>
terminal 103 by backprobing.
(3) Start the engine and run at constant speed of 50km/h
(31mph). (Gear range: 3rd gear)
(4) Check the waveform.
•
The waveform should show a pattern similar to the
illustration. The maximum value should be 4.8 volts and
more and the minimum value 0.8 volts and less. The
output waveform should not contain the noise.
(5) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the waveform normal?
YES : Go to Step 8.
NO : Go to Step 4.
AC001657
CONNECTORS: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>, C-61 <2.4L ENGINE>
OR C-63 <3.0L ENGINE>
PCM
AM
C-54 <2.4L ENGINE>
OR
C-55 <3.0L ENGINE>
C-61 <2.4L ENGINE>
OR
C-63 <3.0L ENGINE>
AC001899
C-61 <2.4L ENGINE> OR C-63 <3.0L ENGINE>
CONNECTOR HARNESS SIDE VIEW
C-54 <2.4L ENGINE> OR C-55 <3.0L ENGINE>
CONNECTOR HARNESS SIDE VIEW
AD
OSCILLO-
SCOPE
PROBE
ACX02131AB
NORMAL WAVEFORM
(V)
5
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст