Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 52
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-17
C A M SH A FT A N D C A M SH A FT O IL SEA L
REMOVAL AND INSTALLATION
M1112001900143
<LEFT BANK>
Required Special Tools:
•
MB990767: End Yoke Holder
•
MB991559: Camshaft Oil Seal Adapter
•
MD998443: Auto-lash Adjuster Holder
•
MD998713: Camshaft Oil Seal Installer
•
MD998715: Crankshaft Pulley Holder Pin
Pre-removal and Post-installation Operation
•
Timing Belt Removal and Installation (Refer to
.)
AC004834
APPLY ENGINE OIL TO
ALL THE MOVING PARTS
WHEN INSTALLING
(ENGINE OIL)
3.4 ± 0.5 N·m
31 ± 4 in-lb
13 ± 2 N·m
109 ± 21 in-lb
88 ± 10 N·m
65 ± 7 ft-lb
31 ± 3 N·m
23 ± 2 ft-lb
1
2
3
5
6
7
8
10
11
AC
4
N
9
N
CAMSHAFT REMOVAL STEPS
•
THERMOSTAT HOUSING
ASSEMBLY (REFER TO GROUP
14, WATER HOSE AND PIPE
1.
BLOW-BY HOSE CONNECTION
2.
PCV HOSE CONNECTION
3.
SPARK PLUG CABLE
4.
BATTERY CABLE CONNECTION
5.
ROCKER COVER
<<A>>
>>D<<
6.
ROCKER ARM AND SHAFT
ASSEMBLY
<<B>>
>>B<<
7.
CAMSHAFT SPROCKET
9.
BATTERY CABLE AND
HARNESS BRACKET
10. THRUST CASE
11. CAMSHAFT
CAMSHAFT OIL SEAL
REMOVAL STEPS
<<B>>
>>B<<
7.
CAMSHAFT SPROCKET
>>A<<
8.
CAMSHAFT OIL SEAL
CAMSHAFT REMOVAL STEPS
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-18
<RIGHT BANK>
Required Special Tools:
•
MB990767: End Yoke Holder
•
MD998443: Auto-lash Adjuster Holder
•
MD998713: Camshaft Oil Seal Installer
•
MD998715: Crankshaft Pulley Holder Pin
Pre-removal and Post-installation Operation
•
Timing Belt Removal and Installation (Refer to
.)
AC001717AB
3.4 ± 0.5 N·m
31 ± 4 in-lb
13 ± 2 N·m
109 ± 21 in-lb
31 ± 3 N·m
23 ± 2 ft-lb
88 ± 10 N·m
65 ± 7 ft-lb
APPLY ENGINE OIL TO
ALL THE MOVING PARTS
WHEN INSTALLING
1
2
3
4
5
6
7
8
9
CAMSHAFT REMOVAL STEPS
•
INTAKE MANIFOLD PLENUM
(REFER TO GROUP 15, INTAKE
MANIFOLD PLENUM
.)
1.
BREATHER HOSE
CONNECTION
2.
BLOW-BY HOSE CONNECTION
3.
SPARK PLUG CABLE
4.
ROCKER COVER
<<A>>
>>D<<
5.
ROCKER ARM AND SHAFT
ASSEMBLY
>>C<<
6.
DISTRIBUTOR
<<B>>
>>B<<
7.
CAMSHAFT SPROCKET
9.
CAMSHAFT
CAMSHAFT OIL SEAL
REMOVAL STEPS
<<B>>
>>B<<
7.
CAMSHAFT SPROCKET
>>A<<
8.
CAMSHAFT OIL SEAL
CAMSHAFT REMOVAL STEPS
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-19
REMOVAL SERVICE POINTS
<<A>> ROCKER ARM AND SHAFT ASSEMBLY REMOVAL
1. Install special tool MD998443 as shown in the illustration so
that the lash adjusters will not fall out.
CAUTION
Never disassemble the rocker arm and shaft assembly.
2. Loosen the rocker arm and shaft assembly mounting bolts,
then remove the rocker arm and shaft assembly with the
bolts still attached.
<<B>> CAMSHAFT SPROCKET REMOVAL
1. Use special tools MB990767 and MD998715 to loosen the
camshaft sprocket mounting bolt.
2. Remove the camshaft sprocket.
INSTALLATION SERVICE POINTS
>>A<< CAMSHAFT OIL SEAL INSTALLATION
1. Apply engine oil to the camshaft oil seal lip.
2. Use special tools MB991559 and MD998713 to press-fit the
camshaft oil seal.
>>B<< CAMSHAFT SPROCKET INSTALLATION
1. Install the camshaft sprocket.
2. Use special tools MB990767 and MD998715 to tighten the
camshaft sprocket mounting bolt to the specified torque.
Tightening torque: 88
±
10 N
⋅
m (65
±
7 ft-lb)
AC001718
MD998443
AB
ACX00301AB
MB990767
MD998715
AC001719 AB
MD998713
MB991559 MD998713
LEFT RANK
RIGHT BANK
ACX00301AB
MB990767
MD998715
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-20
>>C<< DISTRIBUTOR INSTALLATION
1. Align the timing mark of the camshaft sprocket (right bank)
with that of the cylinder head.
2. Align the mating marks on the distributor housing and
coupling, then install the distributor to the engine.
>>D<< ROCKER ARM AND SHAFT ASSEMBLY
INSTALLATION
1. Rotate the camshaft until the dowel pin on its front end is
located as shown in the illustration.
NOTE: Placing the camshaft in the illustrated position
minimizes the amount of cam lift, making it easier to install
the rocker arm and shaft assembly.
2. Temporarily tighten the rocker shaft with the bolts so that all
rocker arms on the inlet valve side do not push the valves.
AC001720
TIMING
MARKS
CAMSHAFT
SPROCKET
(RIGHT BANK)
AB
AC001721AB
MATING MARKS
AC001722
APPROXIMATELY 60˚
APPROXIMATELY 70˚
RIGHT BANK
LEFT BANK
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст