Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 455
![](/vehicles/winoney/isene/butrele/yehescondeve.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-111
STEP 14. Check connectors C-28 at intermediate
connector and C-107 at junction block for damage.
Q: Are the connectors in good condition?
YES : Repair it because of harness open circuit or short
circuit to ground between input shaft speed sensor
connector B-42 terminal 3 and junction block
connector C-107 terminal 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 15. Replace the input shaft speed sensor.
(1) Replace the input shaft speed sensor. Refer to GROUP
23B, Transaxle
(2) Carry out a test drive.
(3) Read in the diagnostic trouble code.
Q: Is the A/T diagnostic trouble code number "22" output?
YES : Go to Step 16.
NO : The inspection is complete.
AC001741 AJ
CONNECTOR: C-28
AC001691
CONNECTOR: C-107
JUNCTION BLOCK
(FRONT VIEW)
AO
AC001835
INPUT SHAFT
SPEED SENSOR
AE
![](/vehicles/winoney/isene/butrele/sshome.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-112
STEP 16. Check connectors C-28 at intermediate
connector and C-107 at junction block for damage.
Q: Are the connectors in good condition?
YES : Go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 17. Check harness for damage between input shaft
speed sensor harness side connector B-42 terminal 2 and
PCM connector C-61 <2.4L Engine> or C-63 <3.0L Engine>
terminal 103.
Q: Is the harness wire in good condition?
YES : Go to Step 18.
NO : Repair it.
AC001741 AJ
CONNECTOR: C-28
AC001691
CONNECTOR: C-107
JUNCTION BLOCK
(FRONT VIEW)
AO
AC001835
CONNECTOR: B-42
AD
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
![](/vehicles/winoney/isene/butrele/whint.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-113
STEP 18. Check harness for damage between input shaft
speed sensor harness side connector B-42 terminal 1 and
PCM connector C-54 <2.4L Engine> or C-55 <3.0L Engine>
terminal 57.
Q: Is the harness wire in good condition?
YES : Go to Step 19.
NO : Repair it.
STEP 19. Check harness for damage between input shaft
speed sensor harness side connector B-42 terminal 3 and
junction block connector C-107 terminal 12.
Q: Is the harness wire in good condition?
YES : Go to Step 20.
NO : Repair it.
AC001835
CONNECTOR: B-42
AD
AC001657
CONNECTOR: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
PCM
AL
AC001835
CONNECTOR: B-42
AD
AC001691
CONNECTOR: C-107
JUNCTION BLOCK
(FRONT VIEW)
AO
![](/vehicles/winoney/isene/butrele/ino.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-114
STEP 20. Replace the underdrive clutch retainer.
(1) Replace the underdrive clutch retainer. Refer to GROUP
23B, Underdrive Clutch and Input Shaft
.
(2) Carry out a test drive.
(3) Read in the diagnostic trouble code.
Q: Is the A/T diagnostic trouble code number "22" output?
YES : The A/T diagnostic trouble code may have set due to
external radio frequency (RFI), possibility caused by
cellular phone activity, after market components
installed on the vehicle, etc.
NO : The inspection is complete.
DTC 23: Output Shaft Speed Sensor System
AC001836AB
AC004685
Output Shaft Speed Sensor System Circuit
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст