Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 219
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-75
TECHNICAL DESCRIPTION
•
The engine coolant temperature sensor converts
the engine coolant temperature to a voltage and
output it.
•
The ECM <M/T> or PCM <A/T> checks whether
this voltage is within a specified range.
DTC SET CONDITIONS
Check Conditions
•
Two seconds or more have passed since the
staring sequence was completed.
Judgement Criteria
•
Engine coolant temperature sensor output
voltage has continued to be 4.6 volts or higher
[corresponding to a coolant temperature of -45
°
C
(-49
°
F) or lower] for 2 seconds.
or
•
Engine coolant temperature sensor output
voltage has continued to be 0.1 volt or lower
[corresponding to a coolant temperature of 140
°
C (284
°
F) or higher] for 2 seconds.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
•
Engine coolant temperature sensor failed.
•
Open or shorted engine coolant temperature
sensor circuit, or loose connector.
•
ECM failed. <M/T>
•
PCM failed. <A/T>
DIAGNOSIS
Required Special Tools
MB991502: Scan Tool (MUT-II)
STEP 1. Using scan tool MB991502, check data list item 21:
Engine Coolant Temperature Sensor.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991502 to the data reading mode for item
21, Engine Coolant Temperature Sensor.
•
The engine coolant temperature and temperature
shown with the scan tool should approximately match.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points (
NO : Go to Step 2.
STEP 2. Check connector B-11 at the engine coolant
temperature sensor for damage.
Q: Is the connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
AKX01177
16 PIN
MB991502
AB
ACX02490
CONNECTOR : B-11
ENGINE
COOLANT
TEMPERATURE
SENSOR
AC
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-76
STEP 3. Check the sensor supply voltage at engine
coolant temperature sensor harness side connector B-11.
(1) Disconnect the connector B-11 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.
•
Voltage should be between 4.5 and 4.9 volts
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 6.
NO : Go to Step 4.
STEP 4. Check connector C-58 at ECM <M/T> or connector
C-55 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
AK000234
B-11 HARNESS
SIDE CONNECTOR
2 1
AB
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-77
STEP 5. Check for open circuit between engine coolant
temperature sensor connector B-11 terminal 1 and ECM
connector C-58 terminal 44 <M/T> or PCM connector C-55
terminal 44 <A/T>.
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 11.
NO : Repair it. Then go to Step 11.
STEP 6. Check the continuity at engine coolant
temperature sensor harness side connector B-11.
(1) Disconnect the connector B-11 and measure at the harness
side.
(2) Check for the continuity between terminal 2 and ground.
•
Should be less than 2 ohm.
Q: Is the continuity normal?
YES : Go to Step 9.
NO : Go to Step 7.
ACX02490
CONNECTOR : B-11
ENGINE
COOLANT
TEMPERATURE
SENSOR
AC
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
AK000235
B-11 HARNESS
SIDE CONNECTOR
AB
2 1
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-78
STEP 7. Check connector C-58 at ECM <M/T> or connector
C-55 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
STEP 8. Check for open circuit between engine coolant
temperature sensor connector B-11 terminal 2 and ECM
connector C-58 terminal 49 <M/T> or PCM connector C-55
terminal 57 <A/T>.
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 11.
NO : Repair it. Then go to Step 11.
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
ACX02490
CONNECTOR : B-11
ENGINE
COOLANT
TEMPERATURE
SENSOR
AC
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст