Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 476
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-196
STEP 8. Using scan tool MB991502, check actuator test
item 02: Underdrive Solenoid Valve.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Set scan tool MB991502 to the actuator test mode for item
02: Underdrive Solenoid Valve.
•
An operation sound should be heard from solenoid
valve when the underdrive solenoid valve is operated.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : This malfunction can be intermittent. Refer to GROUP
00, How to Use Troubleshooting/Inspection Service
Points
−
How to Cope with Intermittent Malfunction
NO : Replace the PCM.
STEP 9. Check connector B-40 at solenoid valve assembly
for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001252
MB991502
16 PIN
AB
ACX02479
CONNECTOR: B-40
AE
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-197
STEP 10. Check the underdrive solenoid valve at solenoid
valve assembly connector B-40.
(1) Disconnect connector B-40 and measure at the solenoid
valve side.
(2) Measure the resistance between terminal 3 and 9.
Standard value: 2.7 - 3.4
Ω
Q: Is the resistance at the standard value?
YES : Go to Step 11.
NO : Replace the underdrive solenoid valve. Refer to
GROUP 23B, Valve Body
.
STEP 11. Check the power supply voltage at solenoid
valve assembly connector B-40.
(1) Disconnect connector B-40 and measure at the harness
side.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 9 and ground.
•
Voltage should be battery positive voltage.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 13.
NO : Go to Step 12.
ACX02479
CONNECTOR: B-40
AE
AC001962
HARNESS
CONNECTOR: B-40
AD
ACX02479
CONNECTOR: B-40
AE
AC001967
HARNESS
CONNECTOR: B-40
AD
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-198
STEP 12. Check connector A-19X at A/T control relay for
damage.
Q: Is the connector in good condition?
YES : Repair it because of harness open circuit or short
circuit to ground between solenoid valve assembly
connector B-40 terminal 9 and A/T control relay
connector A-19X terminal 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 13. Check connectors C-61 <2.4L Engine> or C-63
<3.0L Engine> at PCM connector for damage.
Q: Are the connectors in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 14. Check harness for open circuit, or short circuit to
ground between solenoid valve assembly connector B-40
terminal 3 and PCM connector C-61 <2.4L Engine> or C-63
<3.0L Engine> terminal 120.
Q: Is the harness wire in good condition?
YES : Replace the PCM.
NO : Repair it.
AC001655
CONNECTOR: A-19X
BATTERY
A/T CONTROL
RELAY
AD
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
ACX02479
CONNECTOR: B-40
AE
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-199
DTC 33: Second Solenoid Valve System
Solenoid Valve System Circuit
Refer to
.
CIRCUIT OPERATION
Refer to
.
DTC SET CONDITIONS
If the resistance value for a solenoid valve circuit is
greater than 3.5
Ω
for 4 seconds at 100
°
C (212
°
F) or
less than 2.6
Ω
for 4 seconds at 100
°
C (212
°
F), it is
judged that there is a short circuit or an open circuit
in the solenoid valve and the diagnostic trouble code
number "33" is displayed. The transmission is locked
into 3rd gear as a fail-safe measure, and the "N"
range light flashes once per second.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set:)
•
Malfunction of second solenoid valve
•
Damaged harness, connector
•
Malfunction of the PCM
DIAGNOSIS
Required Special Tool:
MB991502: Scan Tool (MUT-II)
STEP 1. Using scan tool MB991502, read the A/T
diagnostic trouble code.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Read the A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the A/T diagnostic trouble code number "54" output?
, code number 54: A/T control
relay system.
NO : Go to Step 2.
AC001252
MB991502
16 PIN
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст