Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 562
![](/vehicles/winoney/isene/butrele/ouifobe.png)
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-21
>>C<< JAM NUT INSTALLATION
1. Temporarily tighten the jam nut.
CAUTION
Do not use an impact wrench to tighten the jam nut,
otherwise the jam nut will be damaged.
2. Remove special tools MB991237 and MB991239, and then
tighten the jam nut to 23
±
2 N
⋅
m (17
±
1 ft-lb).
AC001074 AB
23 ± 2 N·m
17 ± 1 ft-lb
![](/vehicles/winoney/isene/butrele/fowa.png)
STABILIZER BAR
TSB Revision
REAR SUSPENSION
34-22
STA B ILIZER B A R
REMOVAL AND INSTALLATION
M1341003000032
Required Special Tool:
•
MB990326: Preload Socket
Post-installation Operation
•
Check the Dust Cover for Cracks or Damage by Pushing
it with your Finger.
AC001075
5
4
3
44 ± 10 N·m
33 ± 7 ft-lb
1
2
39 ± 5 N·m
29 ± 4 ft-lb
1
AD
39 ± 5 N·m
29 ± 4 ft-lb
REMOVAL STEPS
1.
STABILIZER LINK MOUNTING
NUTS
2.
STABILIZER LINK
>>A<<
3.
STABILIZER BAR BRACKET
>>A<<
4.
BUSHING
>>A<<
5.
STABILIZER BAR
REMOVAL STEPS (Continued)
![](/vehicles/winoney/isene/butrele/onsy.png)
SPECIFICATIONS
TSB Revision
REAR SUSPENSION
34-23
INSTALLATION SERVICE POINT
>>A<< STABILIZER BAR/BUSHING/STABILIZER BAR
BRACKET INSTALLATION
Position the stabilizer bar identification mark to the left side.
Adjust the identification mark position as shown in the figure,
and tighten the stabilizer bar bracket mounting bolt.
INSPECTION
M1341001400056
•
Check the bushings for wear and deterioration.
•
Check the stabilizer bar for deterioration or damage.
•
Check all bolts for condition and straightness.
STABILIZER LINK BALL JOINT BREAKAWAY TORQUE
CHECK
1. After shaking the ball joint stud several times, install the nut
to the stud and use special tool MB990326 to measure the
breakaway torque of the ball joint.
Standard value: 3.4
−
9.0 N
⋅
m (30
−
80 in-lb)
2. When the measured value exceeds the standard value,
replace the stabilizer link.
3. When the measured value is lower than the standard value,
check that the ball joint turns smoothly without excessive
play. If so, it is possible to re-use that ball joint.
STABILIZER LINK BALL JOINT DUST COVER CHECK
1. Check the dust cover for cracks or damage by pushing it
with your finger.
2. If the dust cover is cracked or damaged, replace the
stabilizer link.
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1341012700073
AC001076 AB
APPROXIMATELY 10 mm (0.4 in)
OUTSIDE OF
THE BODY
AC001129
MB990326
AB
ITEMS
SPECIFICATIONS
Lower arm and toe control arm assembly
Lower arm assembly to crossmember nut
98
±
10 N
⋅
m (73
±
7 ft-lb)
Lower arm assembly to knuckle jam nut
108
±
10 N
⋅
m (80
±
7 ft-lb)
Stabilizer link nut
39
±
5 N
⋅
m (29
±
4 ft-lb)
Toe control arm assembly to crossmember nut
74
±
4 N
⋅
m (55
±
3 ft-lb)
Toe control arm assembly to knuckle jam nut
29
±
4 N
⋅
m (21
±
3 ft-lb)
![](/vehicles/winoney/isene/butrele/zouch.png)
SPECIFICATIONS
TSB Revision
REAR SUSPENSION
34-24
GENERAL SPECIFICATIONS
M1341000200071
COIL SPRING
SERVICE SPECIFICATIONS
M1341000300078
Rear suspension assembly
Brake caliper assembly bolt
60
±
5 N
⋅
m (45
±
3 ft-lb)
Brake hose
15
±
2 N
⋅
m (11
±
1 ft-lb)
Crossmember to body nut
88
±
10 N
⋅
m (65
±
7 ft-lb)
Shock absorber assembly to body nut
44
±
5 N
⋅
m (33
±
3 ft-lb)
Trailing arm assembly to body nut
147
±
10 N
⋅
m (109
±
7 ft-lb)
Upper arm assembly to body bolt
39
±
5 N
⋅
m (29
±
4 ft-lb)
Shock absorber assembly
Shock absorber assembly to body nut
44
±
5 N
⋅
m (33
±
3 ft-lb)
Shock absorber assembly to knuckle bolt
98
±
10 N
⋅
m (73
±
7 ft-lb)
Shock absorber jam nut
23
±
2 N
⋅
m (17
±
1 ft-lb)
Stabilizer bar
Stabilizer bar bracket bolt
44
±
10 N
⋅
m (33
±
7 ft-lb)
Stabilizer link nut
39
±
5 N
⋅
m (29
±
3 ft-lb)
Trailing arm assembly
Trailing arm assembly to body nut
147
±
10 N
⋅
m (109
±
7 ft-lb)
Trailing arm assembly to knuckle nut
128
±
9 N
⋅
m (94
±
7 ft-lb)
Upper arm assembly
Upper arm assembly to body bolt
39
±
5 N
⋅
m (29
±
4 ft-lb)
Upper arm assembly to knuckle nut
98
±
10 N
⋅
m (73
±
7 ft-lb)
Upper arm to upper arm bracket nut
57
±
7 N
⋅
m (42
±
5 ft-lb)
ITEMS
SPECIFICATIONS
ITEMS
SPECIFICATIONS
Wire diameter mm (in)
13.0 (0.51)
Average diameter mm (in)
53
±
1.5
−
93
±
1.5 (2.1
±
0.06
−
3.7
±
0.06)
Free length mm (in)
278 (10.9)
ITEMS
STANDARD VALUE
Toe-in mm (in)
3
±
3 (0.12
±
0.12)
Camber
ECLIPSE
−
1
°
20'
±
30' (Difference between right and
left within 30')
ECLIPSE SPYDER
−
1
°
10'
±
30' (Difference between right and
left within 30')
Dimension for positioning upper arm bracket mm (in)
37.2
±
2 (1.46
±
0.08)
Toe control arm ball joint breakaway torque N
⋅
m (in-lb)
1.0
−
3.1 (8.9
−
27)
Stabilizer link ball joint breakaway torque N
⋅
m (in-lb)
3.4
−
9.0 (30
−
80)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст