Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 560
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-13
INSTALLATION SERVICE POINT
>>A<< STOPPER B/STOPPER A INSTALLATION
1. Install stopper B in the shown direction.
2. Install stopper A in the shown direction while checking that
the notches on stopper A are engaged with the projections
on the trailing arm bushing.
INSPECTION
M1341002300030
•
Check the bushings for wear and deterioration.
•
Check the trailing arm for bends or damage.
AC001059
STOPPER A
STOPPER A
STOPPER B
STOPPER B
TRAILING ARM
TRAILING ARM
NOTCHES AND PROJECTIONS
AB
LOWER ARM AND TOE CONTROL ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-14
LO W ER AR M AN D TO E CO N TR O L A R M ASSEM B LY
REMOVAL AND INSTALLATION
M1341004500063
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
Required Special Tools:
•
MB990326: Preload Socket
•
MB990635 or MB991113: Steering Linkage Puller
•
MB990800: Ball Joint Remover and Installer
Post-installation Operation
•
Check the Dust Cover for Cracks or Damage by Pushing
it with Your Finger.
•
Wheel Alignment Check and Adjustment (Refer to
AC001064
8
8
N
6
2
1
3
N
4
7
5
AD
108 ± 10 N·m*
80 ± 7 ft-lb*
29 ± 4 N·m
21 ± 3 ft-lb
74 ± 4 N·m*
55 ± 3 ft-lb*
39 ± 5 N·m
29 ± 4 ft-lb
98 ± 10 N·m*
73 ± 7 ft-lb*
LOWER ARM ASSEMBLY
REMOVAL STEPS
1.
STABILIZER LINK CONNECTION
2.
WHEEL SPEED SENSOR
MOUNTING BOLTS
3.
LOWER ARM ASSEMBLY AND
KNUCKLE CONNECTING BOLT
4.
LOWER ARM ASSEMBLY
MOUNTING BOLT
5.
LOWER ARM ASSEMBLY
TOE CONTROL ARM ASSEMBLY
REMOVAL STEPS
<<A>>
6.
TOE CONTROL ARM AND
KNUCKLE CONNECTION
<<B>>
7.
TOE CONTROL ARM ASSEMBLY
MOUNTING BOLT
8.
TOE CONTROL ARM ASSEMBLY
LOWER ARM AND TOE CONTROL ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-15
REMOVAL SERVICE POINTS
<<A>> TOE CONTROL ARM AND KNUCKLE
DISCONNECTION
CAUTION
•
Use special tool MB990635 or MB991113 to loosen the
nut only; do not remove it from the ball joint.
•
Tie special tool MB990635 or MB991113 with a cord to
prevent it from falling off.
Use special tool MB990635 or MB991113 to disconnect the toe
control arm and knuckle.
<<B>> TOE CONTROL ARM ASSEMBLY MOUNTING BOLT
REMOVAL
Place mating marks on the crossmember and the plate before
removing the bolt.
INSPECTION
M1341004600060
•
Check the bushings for wear and deterioration.
•
Check the lower arm or toe control arm for bends or
damage.
•
Check all bolts for condition and straightness.
TOE CONTROL ARM BALL JOINT BREAKAWAY TORQUE
CHECK
1. After shaking the ball joint stud several times, in order to
make the ball joint turn smoothly, install the nut to the stud
and use the special tool MB990326 to measure the
breakaway torque of the ball joint.
Standard value: 1.0
−
3.1 N
⋅
m (8.9
−
27 in-lb)
2. When the measured value exceeds the standard value,
replace the toe control arm assembly.
3. When the measured value is lower than the standard value,
check that the ball joint turns smoothly without excessive
play. If so, it is possible to re-use that ball joint.
ACX00715AC
BALL JOINT
CORD
NUT
MB991113 OR
MB990635
AC001065AB
PLATE
MATING MARKS
AC001091
MB990326
AC
LOWER ARM AND TOE CONTROL ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-16
TOE CONTROL ARM BALL JOINT DUST COVER CHECK
1. Check the dust cover for cracks or damage by pushing it
with your finger.
2. If the dust cover is cracked or damaged, replace the toe
control arm assembly.
NOTE: Cracks or damage of the dust cover may cause
damage to the ball joint. When it is damaged during service
work, replace the dust cover.
TOE CONTROL ARM BALL JOINT DUST COVER
REPLACEMENT
M1341014800043
If the dust cover is damaged accidentally during service work,
replace the dust cover as follows:
1. Remove the dust cover.
2. Apply multipurpose grease to inside and lip of the dust
cover.
3. Using special tool MB990800 press the dust cover until it
contacts the snap ring.
4. Check the dust cover for cracks or damage by pushing it
with your finger.
AC001066
MB990800
DUST COVER
SNAP RING
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст