Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 10
SCHEDULED MAINTENANCE TABLE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-37
SCHEDULED MAINTENANCE UNDER SEVERE USAGE CONDITIONS
Maintenance should be carried out according to the following table:
Sever usage conditions:
A: Driving in dusty conditions
B: Trailer towing, or police, taxi, or commercial type operation
C: Extensive idling, driving in stop and go traffic
D: Short-trip operation at freezing temperatures (engine not thoroughly warmed up)
E: Driving in sandy areas
F: Driving in salty areas
G: More than 50% operation in heavy city traffic or at sustained high speeds during hot weather above 32
°
C
(90
°
F)
H: Driving off-road
NO.
MAINTENANC
E ITEM
SERVICE
INTERVALS
KILOMETERS
IN
THOUSANDS
24
48
72
96
120
144 168 SEVERE
USAGE
CONDITION
S
MILEAGE IN
THOUSANDS
15
30
45
60
75
90
105
3
Air cleaner
element
Replace at
X
X
X
X
X
X
X
A and E
5
Spark plugs
Replace at
X
X
X
X
X
X
X
B and D
10
Engine oil
Change every 3 months or
Every 4,800 km (3,000 miles)
A, B, C, D
and G
11
Engine oil filter
Replace every 6 months or
Every 9,600 km (6,000 miles)
A, B, C, D
and G
12
Manual
transmission oil
Change oil at
X
X
X
B, G and H
13
Automatic
transmission
fluid
Change A/T fluid at
X
X
X
B, G and H
15
Disc brake
pads
Inspect for wear every 6
months or
Every 9,600 km (6,000 miles)
A and F
16
Rear drum
brake linings
and rear wheel
cylinders
Inspect for wear every 12
months or
Every 2,400 km (15,000 miles)
A and F
22
Tires
Rotate every 6 months or
Every 9,600 km (6,000 miles)
B, C, E, G
and H
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-38
M A IN TEN A N C E SERVIC E
1. FUEL SYSTEM (TANK, PIPE LINE AND
CONNECTION, AND FUEL TANK FILLER TUBE
CAP) (CHECK FOR LEAKS)
M1001001600099
1. Check for damage or leakage in the fuel lines and
connections.
2. Inspect the surface of fuel hoses for heat and mechanical
damage. Hard and brittle rubber, cracking, checking, tears,
cuts, abrasions and excessive swelling indicate deterioration
of the rubber.
3. If the fabric casing of the rubber hose is exposed by cracks
and abrasions in the fuel system, the hoses should be
replaced.
2. FUEL HOSES (CHECK CONDITION)
M1001001700096
1. Inspect the surface of fuel hoses for heat and mechanical
damage.Hard and brittle rubber, cracking, tears, cuts,
abrasions and excessive swelling indicate deterioration of
the rubber.
2. If the fabric casing of the rubber hose is exposed by cracks
and abrasions in the fuel system, the hoses should be
replaced.
3. AIR CLEANER ELEMENT (REPLACE)
M1001001800093
The air cleaner element will become dirty during use, reducing
its effect. Replace it with a new one.
REPLACEMENT OF AIR CLEANER ELEMENT
1. Unclamp the air cleaner cover.
2. Remove the air cleaner element and install a new one.
3. When clamping the air cleaner cover in place, be sure that
the cover is completed closed.
4. EVAPORATIVE EMISSION CONTROL SYSTEM
(EXCEPT EVAPORATIVE EMISSION CANISTER)
(CHECK FOR LEAKS AND CLOGGING)
M1001001900090
If the fuel-vapor vent line is clogged or damaged, the fuel vapor
mixture will escape into the atmosphere causing excessive
emissions. Disconnect the line at both ends, and blow it clean
with compressed air. Remove the fuel tank filler tube cap from
the filler tube and check to see if there is evidence that the
packing makes improper contact to the filler tube.
AC000074
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-39
5. SPARK PLUGS (REPLACE)
M1001002000078
CAUTION
Platinum plugs are used on 3.0L engine.Use care not to
damage the platinum tips of the platinum plugs.Do not
attempt to adjust the gap on these plugs.
1. Spark plugs must spark properly to assure proper engine
performance and reduce exhaust emission level.
Therefore, they should be replaced periodically with new
ones.
Spark plug type
2. The new plugs should be checked for the proper gap.
Spark plug gap: 1.0
−
1.1 mm (0.039
−
0.043 inch)
3. Install the spark plugs and tighten to 25
±
4 N
⋅
m (18
±
4 ft-lb)
6. IGNITION CABLES (REPLACE)
M1001002100064
CAUTION
When disconnecting an ignition cable, be sure to hold the
cable boot. If the cable is disconnected by pulling on the
cable alone, an open circuit might result.
The ignition cables should be replaced periodically with new
ones. After replacing, make sure that the ignition cables are
routed properly and fully seated.
MAKER
2.4L ENGINE
3.0L ENGINE
NGK
BKR5E-11
PFR6G-11
DENSO
K16PR-U11
PK20PR11
CHAMPION
RC10YC4
RC8PYP4
AKX00383
AKX00383
PLATINUM
TIPS
AD
<3.0L ENGINE>
AKX01272
AKX01272
PLUG GAP
GAUGE
MEASU-
REMENT
DIRECTION
AC
<2.4L ENGINE>
AKX00434
INCORRECT
CORRECT
AC
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-40
7. DISTRIBUTOR CAP AND ROTOR (CHECK)
<3.0L ENGINE>
M1001002200050
Check the distributor cap and rotor to maintain driveability and
reduce exhaust emissions.
DISTRIBUTOR CAP AND ROTOR INSPECTION
Inspect in accordance with the following procedure. Repair or
replace as necessary.
•
Check the cap for cracks.
•
Check the cap and rotor electrodes for damage.
•
Wipe clean the cap and rotor.
•
Clean the corrosion off the terminals inside the distributor
cap.
8. TIMING BELT (REPLACE)
M1001002300091
Replace the belt with a new one according to the maintenance
schedule on
to assure proper engine performance.
For removal and installation procedures, refer to GROUP 11A,
Timing Belt
or 11C, Timing Belt
9. DRIVE BELT (FOR GENERATOR, WATER PUMP,
A/C COMPRESSOR AND POWER STEERING
PUMP) (CHECK CONDITION)
M1001002500073
Water Pump <2.4L ENGINE>, A/C Compressor
<3.0L ENGINE> and Generator Drive Belt Tension
Check and Adjustment
<When using scan tool MB991502>
Required Special Tools:
•
MB991502: Scan Tool (MUT-II)
•
MB991668: Belt Tension Meter Set
AKX01147
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст