Mitsubishi Colt Ralliart. Manual — part 594

REAR WIPER AND WASHER

EXTERIOR

51-38

INSTALLATION SERVICE POINTS
>>A<< WIPER BLADE INSTALLATION

AC101090

AE

A

A

Wiper blade

Backing

Backing

Section A – A

Wiper
blade

Backing

CAUTION

Ensure that the backings are bent in the shown
direction, and then install the backings to the
wiper blade.

>>B<< REAR WIPER ARM AND BLADE
ASSEMBLY

AC207142AB

Wiper blade

Mating mark

Install the wiper arm and blade assembly so that the
blade end stops at the mating mark.

INSPECTION

M1511019101504

REAR WIPER MOTOR CHECK

Inspect the rear wiper motor by removing the har-
ness connector with the motor attached to the vehi-
cle.

OPERATION CHECK OF THE REAR
WIPER MOTOR

CAUTION

Before operating the rear wiper motor, apply
water to the tailgate glass to avoid damage to the
tailgate glass surface or the wiper blade due to
dry wiping.

AC208436

1 2 3 4

1 2 3 4

Check the motor operation by connecting the battery
to the rear wiper motor as shown.

Main

Index

Group

TOC

REAR WIPER AND WASHER

EXTERIOR

51-39

CHECK OF STOP POSITION OF THE
REAR WIPER MOTOR

CAUTION

Before operating the rear wiper motor, apply
water to the tailgate glass to avoid damage to the
tailgate glass surface or the wiper blade due to
dry wiping.

AC208436

1 2 3 4

1 2 3 4

1. Connect the battery to the rear wiper motor as

shown.

2. Disconnect the battery cable from the rear

windshield wiper motor while it is turning and then
check to see that the motor stops.

AC208441

1 2 3 4

1 2 3 4

3. Re-connect the battery as shown.
4. Check to see that the rear windshield wiper motor

runs and then stops at the automatic stop
position.

REAR WASHER FLUID EJECTION CHECK

AC510261AB

Unit: mm

40

80

25

15

83

5

Ceramic line

Rear washer nozzle

Rear washer nozzle perpendicular

Move the nozzle to adjust the position so that the
spray is in the area shown in the illustration.

Main

Index

Group

TOC

MARK

EXTERIOR

51-40

MARK

REMOVAL AND INSTALLATION

M1511011801833

AC600667AB

1

4

5

N

N

2

6

3

1.

Front three-diamond mark (Refer to

P.51-2

)

2.

RALLIART icon mark <RALLIART>
(Refer to

P.51-2

)

>>A<<

3.

Front step plate <RALLIART>

>>A<<

4.

Rear three-diamond mark

>>A<<

5.

COLT mark

>>A<<

6.

RALLIART mark <RALLIART>

INSTALLATION SERVICE POINT
>>A<<MARK APPLICATION

1. Installation position

Attach each mark to the position shown in the
illustration.

AC403306

A

A

285 mm

20 mm

AH

Scuff plate

Front step plate

Section A - A

Front seat attaching
nut

3. Front step plate <RALLIART>

Main

Index

Group

TOC

AC403267

106 mm

AB

Centre line of vehicle

Tailgate outer panel press line

Rear three-diamond mark

4. Rear three-diamond mark

AC206522

9 mm

36 mm

AF

Tailgate outer panel end

Tailgate outer panel press line

Combination lamp end

5. COLT mark

AC403269AC

12 mm

50 mm

RALLIART mark

Tailgate outer panel end

Tailgate outer panel press line

6. RALLIART mark <RALLIART>

MARK

EXTERIOR

51-41

2. Installation procedure

(1) Use 3M ATD part number 8906 or equivalent

to clean the mark installation surfaces on the
body.

CAUTION

When attaching the marks, the ambient tempera-
ture should be 20

− 38°C and the air should be

completely free of dust. If the ambient tempera-
ture is lower than 20

°C, the marks and the places

on the vehicle body where the marks are to be
attached should be heated to 20

− 30°C.

(2) Peel off the protection sheet on the back of the

marks to paste it on the installation position.

Main

Index

Group

TOC