Mitsubishi Colt Ralliart. Manual — part 538
![](/vehicles/winoney/ama/flend/corevla.png)
RESISTOR, BLOWER MOTOR AND OUTSIDE/INSIDE AIR SELECTION DAMPER CONTROL MOTOR
HEATER, AIR CONDITIONER AND VENTILATION
55A-60
RESISTOR, BLOWER MOTOR AND OUTSIDE/INSIDE AIR
SELECTION DAMPER CONTROL MOTOR
REMOVAL AND INSTALLATION
M1552015200105
AC207764AC
3
2
1
Resistor removal step
•
Glove box (Refer to GROUP 52A,
Instrument Panel
•
Front scuff plate and cowl side trim
(Refer to GROUP 52A, Interior Trim
<<
A
>>
1.
Resistor
Blower motor removal step
•
Parking brake pedal assembly
(GROUP 36, Parking Brake Pedal
.)
•
Transmission control cable dash
panel side installation (Refer to
GROUP 23, Transmission control
•
Diagnosis connector bracket
•
Foot heater duct LH (Refer to
2.
Blower motor
Outside/Inside air selection
damper control motor removal
step
•
Glove box (Refer to GROUP 52A,
Instrument Panel
3.
Outside/Inside air selection damper
control motor
Blower motor removal step
Main
Index
Group
TOC
![](/vehicles/winoney/ama/flend/xcoust.png)
RESISTOR, BLOWER MOTOR AND OUTSIDE/INSIDE AIR SELECTION DAMPER CONTROL MOTOR
HEATER, AIR CONDITIONER AND VENTILATION
55A-61
REMOVAL SERVICE POINT
<<A>> RESISTOR REMOVAL
AC209042AB
Air intake box
Driver
To remove the resistor, insert the screwdriver from
the back of air intake box.
INSPECTION
M1552015600084
RESISTER CHECK
1 2
3 4
AC208521
STANDARD VALUE:
Measurement terminal Standard value (
Ω)
Between terminal Nos. 2
and 3
2.45
Between terminal Nos. 1
and 2
0.95
Between terminal Nos. 2
and 4
0.27
BLOWER FAN AND MOTOR CHECK
1 2
AC208520
Check that the motor turns when applying battery
power between the connector terminals. Also check
to see that there is no abnormal sound emitted from
the motor at this time.
OUTSIDE/INSIDE AIR SELECTION
DAMPER CONTROL MOTOR CHECK
CAUTION
Stop energizing when the lever is set to the oper-
ation stopping position.
AC206697
AB
4
1 2 3
7
5 6
Fresh air
position
Recirculation
air position
Connection
(+) terminal
Connection
(-) terminal
Lever operation
1
7
The rotation stops at
the fresh air position
1
5
The rotation stops at
the recirculation air
position
Main
Index
Group
TOC
![](/vehicles/winoney/ama/flend/ndainll.png)
AMBIENT TEMPERATURE SENSOR
HEATER, AIR CONDITIONER AND VENTILATION
55A-62
AMBIENT TEMPERATURE SENSOR
REMOVAL AND INSTALLATION
M1554003400283
AC209046AB
1
Removal step
•
Front bumper (Refer to GROUP 51,
Front Bumper and Radiator Grille
.)
1.
Ambient temperature sensor
INSPECTION
M1554003500116
AMBIENT TEMPERATURE SENSOR
CHECK
AC209192AB
10
8
6
4
2
0
10
20
30
40
–10
0
RESISTANCE
(k
Ω)
TEMPERATURE (˚C)
Check to see that the resistance shown in the graph
is almost satisfied when measuring the resistance
between the sensor terminals under two or more dif-
ferent temperature conditions.
Main
Index
Group
TOC
![](/vehicles/winoney/ama/flend/antalhim.png)
COMPRESSOR ASSEMBLY
HEATER, AIR CONDITIONER AND VENTILATION
55A-63
COMPRESSOR ASSEMBLY
REMOVAL AND INSTALLATION <4A9>
M1552004400804
Pre-removal Operation
• Refrigerant Discharging (Refer to
.)
• Front under cover panel assembly (Refer to GROUP 51,
Front Bumper Assembly
Post-installation Operation
• Refrigerant Charging (Refer to
• Drive Belt Tension Adjustment (Refer to GROUP 11A,
On-Vehicle Service, Drive Belt Tension Check And Adjust-
• Front under cover panel assembly installation (Refer to
GROUP 51, Front Bumper Assembly
.)
AC402365
1, 2
A/C compressor oil: SUN PAG 56
3
3
N
4
2
1
6
5
AB
25 ± 4 N·m
22 ± 2 N·m
-Pipe coupling
Removal steps
<<
A
>>
1.
Flexible suction hose connection
<<
A
>>
2.
Flexible discharge hose connection
3.
O-ring
<<
B
>>
4.
Drive belt
<<
C
>>
>>
A
5.
A/C compressor assembly
6.
A/C compressor bracket
7.
A/C drive belt tensioner assembly
Removal steps (Continued)
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст