Mitsubishi Colt Ralliart. Manual — part 201
![](/vehicles/winoney/ama/flend/ustowig.png)
TRANSMISSION CONTROL
CVT
23A-147
REMOVAL SERVICE POINTS
<<A>> KEY INTERLOCK ROD REMOVAL
CAUTION
Do not bend the key interlock rod cable.
Turn the ignition switch to the ACC position and then
pull the key interlock rod out from the ignition key cyl-
inder.
INSTALLATION SERVICE POINTS
>>A<< TRANSMISSION CONTROL
CABLE (TRANSMISSION SIDE) INSTAL-
LATION
AC103395AD
Adjusting nut
Transmission
control cable
1. Shift the selector lever and manual control lever to
the N position.
2. Gently push the transmission control cable in the
direction of the arrow (with a force of
approximately 5 N) to tighten the adjusting nut to
the specified torque.
Tightening torque: 12
± 2 N⋅m
>>B<< TRANSMISSION CONTROL
CABLE (SELECTOR LEVER SIDE)
INSTALLATION
Ensure that the transmission control cable is con-
nected securely.
>>C<< SHIFT LOCK CALBLE UNIT/SHIFT
LOCK ROD INSTALLATION
CAUTION
Do not bend the shift lock cable.
1. Shift the selector lever to the P position and turn
the ignition switch to the LOCK (OFF) position.
AC208298
AB
Bolt
Rod
Lock cam
Shift lock cable
unit
2. After installing the shift lock rod to the lock cam of
the selector lever assembly, tighten the bolts of
the shift lock cable unit to the specified torque.
Tightening torque: 5.0
± 1.0 N⋅m
>>D<< KEY INTERLOCK ROD
INSTALLATION
CAUTION
Do not bend the key interlock rod cable.
Turn the ignition switch to the ACC position and then
install the key interlock rod through the ignition key
cylinder.
Main
Index
Group
TOC
![](/vehicles/winoney/ama/flend/eandin.png)
CVT KEY INTERLOCK AND SHIFT LOCK MECHANISMS
CVT
23A-148
CVT KEY INTERLOCK AND SHIFT LOCK MECHANISMS
REMOVAL AND INSTALLATION
M1231203400144
CAUTION
When removing and installing the shift lock cable unit, be careful not to hit the SRS-ECU.
Pre-removal Operation
• Steering column lower cover and instrument lower panel
removal (Refer to GROUP 52A, Instrument Panel Assem-
bly
).
Post-installation Operation
• Key interlock and shift lock mechanism check (Refer to
).
• Selector lever operation check (Refer to
).
• Steering column lower cover and instrument lower panel
installation (Refer to GROUP 52A, Instrument Panel
Assembly
).
AC208300AB
1
2
4
5.0 ± 1.0 N·m
3
Removal steps
•
Connectors and clamps around
steering column assembly
1.
Shift lock cable connection
<<
A
>> >>
B
<< 2.
Key interlock rod connection
>>
A
<< 3.
Shift lock rod connection
>>
A
<< 4.
Shift lock cable unit
Removal steps (Continued)
Main
Index
Group
TOC
![](/vehicles/winoney/ama/flend/ontathe.png)
CVT KEY INTERLOCK AND SHIFT LOCK MECHANISMS
CVT
23A-149
REMOVAL SERVICE POINTS
<<A>> KEY INTERLOCK ROD REMOVAL
CAUTION
Do not bend the key interlock rod cable.
Turn the ignition switch to the ACC position and then
pull the key interlock rod out from the ignition key cyl-
inder.
INSTALLATION SERVICE POINTS
>>A<< SHIFT LOCK CALBLE UNIT/SHIFT
LOCK ROD INSTALLATION
CAUTION
Do not bend the shift lock cable.
1. Shift the selector lever to the P position and turn
the ignition switch to the LOCK (OFF) position.
AC208298
AB
Bolt
Rod
Lock cam
Shift lock cable
unit
2. After installing the shift lock rod to the lock cam of
the selector lever assembly, tighten the bolts of
the shift lock cable unit to the specified torque.
Tightening torque: 5.0
± 1.0 N⋅m
>>B<< KEY INTERLOCK ROD
INSTALLATION
CAUTION
Do not bend the key interlock rod cable.
Turn the ignition switch to the ACC position and then
install the key interlock rod to the ignition key cylin-
der.
Main
Index
Group
TOC
![](/vehicles/winoney/ama/flend/odd.png)
TRANSMISSION ASSEMBLY
CVT
23A-150
TRANSMISSION ASSEMBLY
REMOVAL AND INSTALLATION
M1231203600201
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened after placing the
vehicle on the earth and loading the full weight of the engine on the vehicle body.
Pre-removal Operation
• Front Under Cover Panel AssemblyRemoval (Refer to
GROUP 51, Front Bumper Assembly and Radiator Grille
).
• Transmission Fluid Draining (Refer to
• Air Cleaner Assembly Removal (Refer to GROUP 15
).
• Battery and Battery Tray Removal.
• Wiper Arm and Blade Assembly and Front Deck Garnish
Removal (Refer to GROUP 51, Windshield Wiper
• Cowl Top Panel Removal (Refer to GROUP 42, Loose
Panel
• Front Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Driveshaft Removal (Refer to GROUP 26
).
Post-installation Operation
• Driveshaft Installation (Refer to GROUP 26
).
• Front Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Cowl Top Panel Installation (Refer to GROUP 42, Loose
Panel
• Wiper Arm and Blade Assembly and Front Deck Garnish
Installation (Refer to GROUP 51, Windshield Wiper
• Battery and Battery Tray Installation.
• Air Cleaner Assembly Installation (Refer to GROUP 15
).
• Front Under Cover Panel Assembly Installation (Refer to
GROUP 51, Front Bumper Assembly and Radiator Grille
).
• Transmission Fluid Refilling (Refer to
)
AC402909AF
1
2
3
11
12
23 ± 3 N·m
12 ± 2 N·m
48 ± 6 N·m
4
5
6
9
8
7
10
N
Removal steps
1.
Transmission control cable
connection
2.
Battery earth
3.
Primary pressure sensor harness
connector
4.
Inhibitor switch connector
Removal steps (Continued)
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст