Acura RL (1996-2004 year). Manual — part 324
Special Tools
Ref. No.
Tool Number
Description
Qty
Page Reference
A973X - 041 - XXXXX Vacuum Pump/Gauge, 0-30 in.Hg.
Main Menu
Table of Contents
Engine Removal/Installation
Removal
Make sure jacks and safety stands are placed properly
and hoist brackets are attached to the correct positions
on the engine.
Make sure the vehicle will not roll off stands and fall
while you are working under it.
CAUTION:
Use fender covers to avoid damaging painted sur-
faces.
Unplug the wiring connectors carefully while holding
the connector portion to avoid damage.
Mark all wiring and hoses to avoid misconnection.
Also, be sure that they do not contact other wiring
or hoses or interfere with other parts.
NOTE: Do the PCM Memory Setting after reconnecting
).
1. Move the front passenger's seat forward.
2. '96 - 98 models: Remove the support struts from the
hood. Fix the hood in a vertical position, then rein-
stall the support struts by using 6 x 1.0 mm bolts.
'99 - 01 models: Remove the hood (see page
).
6 x 1.0 mm bolt
SUPPORT
STRUT
3. Make sure you have the anti-theft code for the radio,
then write down the frequencies for the radio's pre-
set buttons.
4. Disconnect the battery negative terminal first, then
the positive terminal.
5. Remove the strut brace.
STRUT BRACE
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
6. Remove the engine cover.
NOTE: Tighten the bolts/nuts on the engine cover in
the numbered sequence shown ( - ).
6 x 1.0 mm
9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)
ENGINE COVER
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
Main Menu
Table of Contents
Engine Removal/Installation
Removal (cont'd)
7. Remove the intake air duct and air cleaner housing
assembly.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
INTAKE AIR
DUCT
AIR CLEANER
HOUSING
ASSEMBLY
8. Remove the throttle cover.
9. Remove the throttle cable and cruise control cable
by loosening the locknuts, then slip the cable ends
out of the accelerator linkage.
NOTE:
Take care not to bend the cables when removing
them. Always replace any kinked cable with a
new one.
Adjust the throttle cable when installing (see
).
Adjust the cruise control cable when installing
(see
).
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
THROTTLE COVER
THROTTLE
CABLE
CRUISE
CONTROL
CABLE
LOCKNUTS
ADJUSTING
NUTS
10. Raise the coolant reservoir, then remove the battery
and battery base.
11. Remove the relay box, ground cable and engine
wire harness clamps.
ENGINE WIRE
HARNESS CLAMP
6 x 1.0 mm
12 N-m (1.2 kgf-m, 8.7 Ibf-ft)
GROUND
CABLE
RELAY BOX
BATTERY
BASE
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
Main Menu
Table of Contents
12. Remove the vacuum hose, then remove the clamp
from the under-hood fuse/relay box.
VACUUM
HOSE
CLAMP
13. Remove the alternator and battery cables from the
under-hood fuse/relay box, then remove the under-
hood fuse/relay box.
ALTERNATOR
CABLE
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
BATTERY
CABLE
UNDER-HOOD
FUSE/RELAY
BOX
14. Disconnect the engine wire harness connector on
the left side of the engine compartment.
15. Remove the connector and engine wire harness
clamp.
CONNECTOR
ENGINE WIRE
HARNESS
CONNECTOR
CLAMP
6 x 1.0 mm
12 N-m (1.2 kgf-m, 8.7 Ibf-ft)
16. Relieve fuel pressure by loosening the service bolt
on the fuel filter about one turn (see
).
Do not smoke while working on the
fuel system. Keep open flame and sparks away from
the work area. Drain fuel only into an approved
container.
17. Remove the fuel feed hose and fuel return hose.
SERVICE BOLT
12 N-m (1.2 kgf-m, 8.7 Ibf-ft)
WASHER
Replace.
27 N-m (2.8 kgf-m,
20 Ibf-ft)
WASHERS
Replace.
FUEL FEED
HOSE
FUEL RETURN
HOSE
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст