Defender (1993+). Manual — part 87

CHASSIS AND BODY

9.

Fit the bezels to the locking button and

Fitting regulator

remote control lever.

10.

Fit the single screw behind the remote control

lever.

channel.

11.

Fit the door pull and secure with two screws

and finishers.

12.

Fit the window regulator handle and retain
with the single screw and finisher.

5.

Insert the lifting arm button into

the lifting

REMOVING WINDOW

REGULATORS

DEFENDER 110 - Rear

side door

Remove

1.

Remove the door trim.

2.

Remove the protective weather sheet.

3.

Temporarily

fit

the handle and wind the

window up to its fullest extent and support the
glass in this position, with a length

of

timber,

6.

Position the regulator

so

that the fixing holes

to prevent it falling when removing the

line-up with the holes in the mounting panel.

regulator.

7.

Secure with the four screws and tighten

regulator to the mounting panel and withdraw

8.

Temporarily fit the handle and check that

the regulator whilst sliding the lifting

arm

glass

can

be raised and lowered smoothly

button

from

the lifting channel.

To

assist this

without tight spots.

operation, remove the timber and lower the

9. Fit the weather protection sheet with adhesive

glass.

10.

Fit the door trim, regulator handle, door pull,
and bezels.

4.

Remove the four screws retaining the

evenly.

8

REVISED: OCT

1993

CHASSIS AND BODY

REMOVING EXTERIOR HANDLE
DEFENDER 110 - rear side door

Remove

Remove

REMOVING DOOR LOCKING BUTTON
DEFENDER 110 - Rear side door

1.

Remove the door trim, regulator handle, door

1.

Remove the door trim, regulator handle, door

pull and bezels.

pull and bezels.

2.

Peel back sufficient of the weather protection

2.

Peel back sufficient of the weather protection

sheet to

gain access to the handle

sheet to reveal the mechanism

mechanism.

3.

Release the spring clip securing the button to

3. Disconnect the actuating rod from the handle

the operating rod and withdraw

the

rod

from

operating lever.

the button.

4.

Remove the two screws and withdraw the

4.

Remove the two screws securing

the

button to

handle and bezels.

the door panel and remove

the

button

Fitting handle

5.

Fit the handle to the door ensuring that the

two

bezels are i n position - flat faces towards

the door and secure with the two screws.

Fitting locking button

5.

Secure the locking button assembly

to

the

door panel with the two screws.

6.

Fit

the operating rod to the button assembly

and secure with the spring clip

7 . Re-seal the weather protection sheet and

fit

the door trim, door pull, regulator handle and
bezels.

6. Connect the actuating rod to the handle

operating lever and secure with spring clip.

7

Re-seal the weather protection sheet.

8. Fit the door trim. regulator handle, door pull

and bezels.

REVISED: OCT

1993

9

CHASSIS

AND BODY

Fitting control lever

REMOVING REMOTE

CONTROL LEVER

DEFENDER 110 -

Rear side door

9.

Fit the plastic retaining clips to

the

rod

Remove

assembly into position and secure

with the

two screws.

1.

Remove the door trim, door pull, regulator

10, Connect the control rods to the latch

handle and bezels.

assembly and secure with the clips

2. Peel-back sufficient

of

the weather protection

11.

Fit the plastic retaining rod clips to the

sheet to gain access to the remote lever.

mounting panel.

3.

Remove the spring clip and disconnect the

12. Connect the control rod

to

the locking button

control

rod from the locking button.

and secure with the clip.

13. Re-seal the weather protection sheet and

fit

the trim panel, regulator handle, door pull and

bezels.

REMOVING DOOR LATCH ASSEMBLY
DEFENDER 110 -

Rear

side door

Remove

1.

Remove the door pull. regulator handle,
bezels and door

trim.

2.

Peel-back sufficient

of

the weather protection

sheet to reveal the latch.

3. Release the remote control lever rod from the

latch assembly.

4.

Disconnect the door outer handle control rod
from the latch assembly.

5. Disconnect the door locking button remote

control rod from the latch mechanism.

6.

Remove the three retaining screws and
withdraw the latch assembly

from

the door

4. Release the spring clip and disconnect the

short

locking button control rod from the latch

mechanism.

5.

Disconnect the long remote control rod from
the latch assembly.

6. Remove the

two

screws securing the remote

control lever

to

the mounting panel.

7. Release the control

rods

from the plastic

retaining clips located in

the

mounting panel.

8. Withdraw the remote control lever and

rods

from the door.

10

REVISED: OCT 1993

CHASSIS

AND

BODY

Fitting

the latch

7.

Remove the four screws retaining

the

mounting panel to the door and remove

the

panel complete with rods and control lever

7.

Fit

the latch assembly to the door and secure

with the three screws, noting that the
uppermost screw is longer.

8.

Connect the remote control levers to the latch
mechanism reversing instructions 3, 4 and 5.

9.

Re-seal the weather protection sheet and

fit

the regulator handle, door pull, door trim and
bezels.

REMOVING DOOR

GLASS

DEFENDER 110

Rear

side

door

Remove

1.

Disconnect the door check rod from the door

post.

2.

Remove the regulator handle, door pull,

bezels and door trim.

3.

Remove the weather protection sheet.

4.

Remove the window regulator assembly.

5.

Disconnect and remove the door locking

button.

6.

Disconnect the control rods from the latch and

door outer handle mechanism.

8.

Remove the single self tapping screw

to

remove the water channel.

9. Remove the door check torsion bar

10.

Remove the door check rod by bending back
the end stop to enable the rod

to

be

withdrawn.

REVISED:

OCT

1993