Toyota Camry (2018 year). Manual — part 21
94
2. Instrument cluster
Vehicle settings
Item
Settings
Details
BSM (Blind Spot Monitor) (if equipped) (
Outside rear view
mirror indicator
brightness
Bright
Select to change the brightness
of the outside rear view mirror
indicators.
Dim
RCTA (Rear Cross Traffic Alert) (if equipped) (
RCTA buzzer vol-
ume
1 (Low)
Select to change the volume of
the RCTA buzzer.
2 (Medium)
3 (Loud)
TPWS (Tire pressure warning system) (
Set pressure (tire pressure warning sys-
tem initialization)
Select to initialize the tire pres-
sure warning system. To per-
form initialization, press and hold
the
switch.
Before performing initialization,
make sure to adjust the inflation
pressure of each tire to the spec-
ified level. (
Change wheel (change the tire pres-
sure warning system sensor ID code
set)
(vehicles without a tire inflation pres-
sure display function)
Select to change the tire pres-
sure warning system sensor ID
code set.
To enable this function, a second
set of tire pressure warning sys-
tem sensor ID codes must be
registered by a Toyota dealer.
For information regarding chang-
ing the registered ID code set,
contact your Toyota dealer.
(
Change wheel (register tire pressure
warning system sensor ID codes)
(vehicles with a tire inflation pressure
display function)
Select to register the ID codes of
the tire pressure sensors to the
tire pressure warning system.
To register the ID codes, press
and hold the
switch.
(
95
2. Instrument cluster
2
Instrum
e
nt clus
ter
Meter settings
Scheduled maintenance display (if equipped)
Maintenance data reset
Select to reset the message indi-
cating maintenance is required,
after the required maintenance is
performed. (
Item
Settings
Details
Item
Settings
Details
Language
Select to change the language
displayed.
Units
Select to change the units of
measure displayed.
(Eco Driving
Indicator Light)
On
Select to enable/disable the Eco
Driving Indicator Light. (
Off
Drive information
(total [after reset])
Average vehicle
speed
Select to change the display
between average speed/elapsed
time.
Elapsed time
Pop-up display
Incoming calls
Select to enable/disable the pop-
up display.
Brightness adjust-
ment
Default setting
Select to reset the meter display
settings to the default setting.
96
2. Instrument cluster
Odometer
Displays the total distance the vehicle has been driven.
■
Trip meter A/trip meter B
Displays the distance the vehicle has been driven since the meter
was last reset. Trip meters A and B can be used to record and dis-
play different distances independently.
To reset, display the desired trip meter and press and hold the “ODO/
TRIP” switch.
Displays suggestions to the driver in the following situations. To select
a response to a displayed suggestion, use the meter control switches.
The suggestion function can be turned on/off.
(Customizable features:
■
Suggestion to turn off the headlights
If the headlights are left on for a certain amount of time after the
engine switch has been turned off, if the headlight switch is in the
“AUTO” position, a suggestion message will be displayed asking if
you wish to turn the headlights off. To turn the headlights off, select
“Yes”.
If a front door is opened after the engine switch is turned off, this sug-
gestion message will not be displayed.
Odometer/trip meter
Suggestion function
97
2. Instrument cluster
2
Instrum
e
nt clus
ter
Eco Driving Indicator
Eco Driving Indicator will not operate under the following conditions:
●
The shift lever is in any position other than D.
●
A paddle shift switch (if equipped) is operated.
●
The vehicle speed is approximately 80 mph (130 km/h) or higher.
■
Suspension of the settings display
●
Some settings cannot be changed while driving. When changing settings,
park the vehicle in a safe place.
●
If a warning message is displayed, operation of the settings display will be
suspended.
■
Tire pressure (vehicles with a tire inflation pressure display function)
●
It may take a few minutes to display the tire inflation pressure after the
engine switch is turned to the “ON” position (vehicles without a smart key
system) or IGNITION ON mode (vehicles with a smart key system). It may
also take a few minutes to display the tire inflation pressure after inflation
pressure has been adjusted.
●
“---” may be displayed if the tire position information cannot be determined
due to unfavorable radio wave conditions.
●
Tire inflation pressure changes with temperature. The displayed values may
also be different from the values measured using a tire pressure gauge.
■
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
■
Customization
Some functions can be customized. (
Eco Driving Indicator Light
During Eco-friendly acceleration (Eco
driving), the Eco Driving Indicator Light
will turn on. When the acceleration
exceeds the Zone of Eco driving, or
when the vehicle is stopped, the light
turns off.
Eco Driving Indicator Zone Display
Suggests the Zone of Eco driving with
current Eco driving ratio based on
acceleration.
Eco driving ratio based on acceleration
If the acceleration exceeds the Zone of
Eco driving, the right side of the Eco
Driving Indicator Zone Display will illu-
minate.
Zone of Eco driving
1
2
3
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст