Toyota Sequoia (2005). Manual — part 775
SA249–03
F07266
Cutout
–
SUSPENSION AND AXLE
FRONT STABILIZER BAR
SA–93
3089
INSTALLATION
1.
INSTALL STABILIZER BAR LINKS
(a)
Install the 2 bushings, retainers and stabilizer bar link to
the stabilizer bar.
(b)
Hold the stabilizer bar link, and install a new nut.
Torque: 19 N·m (190 kgf·cm, 14 ft·lbf)
(c)
Use the same procedures described above to the other
side.
2.
INSTALL STABILIZER BAR
(a)
Install the 2 bushings with their cutout facing to the rear-
ward of the stabilizer bar.
(b)
Install the stabilizer bar and 2 brackets with the nuts and
bolts.
Torque: 37 N·m (377 kgf·cm, 27 ft·lbf)
3.
CONNECT STABILIZER BAR LINKS TO LOWER SUS-
PENSION ARM
Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
HINT:
If the ball joint turns together with the nut, use a hexagon (6 mm)
wrench to hold the nut.
SA17R–04
F14272
122 (1,244, 90)
Oil Seal
O–ring
Parking Brake Assembly
Disc
Brake Caliper
Bearing Retainer
Speed Sensor Rotor
Snap Ring
Bearing Retainer
Spring Washer
Backing Plate
Serration Bolt
Hub Bolt
Oil Deflector
Gasket
Axle Shaft
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
x6
105 (1,070, 77)
15.5 (158, 11)
Clip
Parking Brake Cable
Hub Bolt
8.0 (82, 71 in.·lbf)
Bearing Assembly
SA–94
–
SUSPENSION AND AXLE
REAR AXLE SHAFT
3090
REAR AXLE SHAFT
COMPONENTS
SA17S–04
F14273
SST
F14274
F14275
–
SUSPENSION AND AXLE
REAR AXLE SHAFT
SA–95
3091
REMOVAL
1.
REMOVE REAR WHEEL
Torque: 110 N·m (1,150 kgf·cm, 83 ft·lbf)
2.
DISCONNECT BRAKE LINE
Using SST, disconnect the brake line and remove the clip.
SST
09023–00101
Torque: 15.5 N·m (158 kgf·cm, 11 ft·lbf)
3.
REMOVE BRAKE CALIPER AND DISC
Remove the 2 bolts, brake caliper and disc.
Torque: 105 N·m (1,070 kgf·cm, 77 ft·lbf)
4.
CHECK BEARING BACKLASH AND AXLE SHAFT
DEVIATION
(a)
Using a dial indicator, check the backlash in the bearing
shaft direction.
Maximum: 0.6 mm (0.024 in.)
If the backlash exceeds the maximum, replace the bearing.
(b)
Using a dial indicator, check the deviation at the surface
of the axle shaft outside the hub bolt.
Maximum: 0.1 mm (0.0040 in.)
If the deviation exceeds the maximum, replace the axle shaft.
5.
REMOVE PARKING BRAKE ASSEMBLY
(a)
Remove the parking brake assembly (See page
(b)
Remove the 2 bolts and pull out the parking brake cable
from the backing plate.
Torque: 8.0 N·m (82 kgf·cm, 71 in.·lbf)
(c)
Use the same procedures described above to the other
side.
F14276
SA–96
–
SUSPENSION AND AXLE
REAR AXLE SHAFT
3092
6.
REMOVE AXLE SHAFT ASSEMBLY
(a)
Remove the 4 nuts.
Torque: 122 N·m (1,244 kgf·cm, 90 ft·lbf)
(b)
Pull out the axle shaft assembly.
NOTICE:
Be careful not to damage the oil seal.
(c)
Remove the O–ring from the axle housing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст