Toyota Sequoia (2005). Manual — part 900
H16692
H16693
H17630
2 jet type:
3 jet type:
A
H
I
J
B
A
C
D
E
D
F
F
D
E
E
D
F
J
J
H
I
B
G
G
G
BO460–01
BO–36
–
BODY
FRONT WIPER AND WASHER
3589
INSPECTION
INSPECT WASHER NOZZLE
While operating the washer, check whether the point where the
washer fluid hits the windshield and the surge area are within
the range indicated by hatched line.
A: Approx. 50 mm (1.97 in)
B: Approx. 40 mm (1.57 in)
C: Approx. 10 mm (0.39 in)
D: Approx. 150 mm (5.91 in)
E: Approx. 110 mm (4.33 in)
F: Approx. 180 mm (7.09 in)
G: Approx. 60 mm (2.36 in)
H: Approx. 310 mm (12.20 in)
I: Approx. 298 mm (11.69 in)
J: Approx. 455 mm (17.91 in)
BO461–01
BE3367
2.0 – 2.5 mm
(0.079 – 0.098 in.)
0.7 – 0.75 mm
(0.028 – 0.0295 in.)
–
BODY
FRONT WIPER AND WASHER
BO–37
3590
ADJUSTMENT
ADJUST WASHER NOZZLE
Using a tool like the one shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid hits the windshield.
BO462–01
H02485
Wiper Link
Cowl Panel
H09483
A
B
C
C
BO–38
–
BODY
FRONT WIPER AND WASHER
3591
INSTALLATION
1.
INSTALL WASHER NOZZLES
2.
INSTALL WIPER LINK
Install the wiper link through the service hole, then torque the
6 bolts.
Torque: 5.5 N·m (56 kgf·cm, 49 in.·lbf)
3.
INSTALL WIPER MOTOR
(a)
Install the wiper motor to the wiper link.
HINT:
When installing the wiper motor, connect the claw of wiper link
to the cowl panel shown in the illustration.
(b)
Torque the 4 bolts.
Torque: 5.5 N·m (56 kgf·cm, 49 in.·lbf)
(c)
Connect the connector.
4.
INSTALL HOOD TO COWL TOP SEAL
Install the hood to cowl top seal to the cowl top ventilator louver.
5.
INSTALL COWL TOP VENTILATOR LOUVER
Install the cowl top ventilator louver with the 8 screws and 6
clips.
6.
INSTALL WIPER ARMS
(a)
Operate the wiper once and turn the wiper switch OFF.
(b)
Install the wiper arms and tighten the nuts by hand.
(c)
Adjust the installation positions of the wiper arms to the
positions shown in the illustration.
A: Approx. 25.4 mm (1.000 in)
B: Approx. 40.0 mm (1.574 in)
HINT:
When installing the wiper arms, make sure that the tips of the
blades are not beyond the ceramic edge as indicated ”C” part
in the illustration.
(d)
Torque the 2 nuts.
Torque: 20 N·m (205 kgf·cm, 15 ft·lbf)
(e)
Install the 2 caps.
BO463–01
H16777
Washer Nozzle
Back Door Glass
Rear Wiper Arm
Back Door Center Garnish
Back Door
Side Garnish
Power Window
Regulator
Step Liner
Service Hole Cover
Wiper Motor
Grommet
Rear Wiper Motor
Back Door Side Garnish
No. 2 Service
Hole Cover
Strap Cover
No. 1 Service Hole Cover
Back Door Trim Board
Back Door Pull Strap
: Specified torque
N·m (kgf·cm, ft·lbf)
5.5 (56, 49 in.·lbf)
8.0 (82, 71 in.·lbf)
5.5 (56, 49 in.·lbf)
8.0 (82, 71 in.·lbf)
–
BODY
REAR WIPER AND WASHER
BO–39
3592
REAR WIPER AND WASHER
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст