Toyota Sequoia (2005). Manual — part 846
H23879
RS11I–01
RS–90
–
SUPPLEMENTAL RESTRAINT SYSTEM
FRONT AIRBAG SENSOR
3373
INSTALLATION
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the front airbag sensor involved in a col-
lision when the airbag has deployed.
If the front airbag sensor center has been dropped, or
there are any cracks, dents or other defects in the
case, bracket or connector, replace it with a new one.
When installing the front airbag sensor center, be
careful that the SRS wiring does not interfere with
other parts and that it is not pinched between other
parts.
After installing, shake the front airbag sensor to
check that there is no looseness.
1.
INSTALL FRONT AIRBAG SENSORS
LH
(a)
Install the front airbag sensors LH with the 2 nuts.
Torque: 17.5 N·m (179 kgf·cm, 13 ft·lbf)
(b)
Connect the front airbag sensor connectors.
2.
CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
3.
PERFORM INITIALIZATION (SEE PAGE
Some system need initialization when disconnecting the cable
from the negative battery terminal.
4.
RS11J–01
H23903
: Specified torque
N·m (kgf·cm, ft·lbf)
Front Door Scuff Plate
Center Pillar Lower Garnish
Front Seat Outer
Belt Retractor
Side Airbag Sensor
Assembly LH
Rear Door Scuff Plate
Front Seat Outer Belt Floor Anchor
17.5 (179, 13)
–
SUPPLEMENTAL RESTRAINT SYSTEM
SIDE AIRBAG SENSOR ASSEMBLY
RS–91
3374
SIDE AIRBAG SENSOR ASSEMBLY
COMPONENTS
RS11K–01
H20066
RS–92
–
SUPPLEMENTAL RESTRAINT SYSTEM
SIDE AIRBAG SENSOR ASSEMBLY
3375
REMOVAL
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
If the wiring connector of the SRS is disconnected
with the ignition switch in the ON position, DTCs will
be recorded.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
Never reuse the side airbag sensor assembly if the
airbag has previously deployed in a collision.
1.
PRECAUTION (SEE PAGE
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3.
REMOVE FRONT DOOR SCUFF PLATE
(SEE PAGE
4.
REMOVE REAR DOOR SCUFF PLATE
(SEE PAGE
5.
REMOVE FRONT SEAT OUTER BELT FLOOR AN-
CHOR (SEE PAGE
6.
REMOVE CENTER PILLAR LOWER GARNISH
(SEE PAGE
)
7.
REMOVE FRONT SEAT OUTER BELT RETRACTOR
(SEE PAGE
)
8.
REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH
(a)
Disconnect the connector from the side airbag sensor as-
sembly LH.
(b)
Remove the 3 bolts and the side airbag sensor assembly
LH.
RS11L–01
–
SUPPLEMENTAL RESTRAINT SYSTEM
SIDE AIRBAG SENSOR ASSEMBLY
RS–93
3376
INSPECTION
1.
VEHICLE NOT INVOLVED IN COLLISION
Perform a diagnostic system check (see page
2.
VEHICLE INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED
Perform a diagnostic system check (see page
3.
VEHICLE INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED
Replace the side airbag sensor assembly (see page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст