Toyota Sequoia (2005). Manual — part 844
![](/vehicles/linovind/vere/fry/scoil.png)
RS0BL–11
H23231
RS–82
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
3365
REMOVAL
NOTICE:
If the wiring connector of the SRS is disconnected
with the ignition switch in the ON position, DTCs will
be recorded.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1.
PRECAUTION (SEE PAGE
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
Never reuse an airbag sensor assembly if the airbag
has previously deployed in a collision.
3.
REMOVE SHIFTING HOLE COVER (SEE PAGE
)
4.
REMOVE UPPER CONSOLE PANEL (SEE PAGE
)
5.
REMOVE REAR CONSOLE BOX (SEE PAGE
)
6.
REMOVE FRONT CONSOLE BOX (SEE PAGE
)
7.
REMOVE AIRBAG SENSOR ASSEMBLY
(a)
Disconnect the holder (with connectors) from the airbag
sensor assembly.
(b)
Remove the 4 bolts and airbag sensor assembly.
RS0BM–06
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
RS–83
3366
INSPECTION
1.
VEHICLE NOT INVOLVED IN COLLISION
Perform a diagnostic system check (see page
2.
VEHICLE INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED
Perform a diagnostic system check (see page
3.
VEHICLE INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED
Replace the airbag sensor assembly (see page
RS0BN–05
RS–84
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
3367
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the airbag sensor assembly with a new one.
The SRS has been deployed in a collision.
The airbag sensor assembly has been found to be faulty in troubleshooting.
The airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the airbag sensor assembly, see page
. Be sure to
follow the correct procedure.
![](/vehicles/linovind/vere/fry/nstha.png)
RS0BO–11
H23231
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
RS–85
3368
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.
If the airbag sensor assembly center has been
dropped, or there are any cracks, dents or other de-
fects in the case, bracket or connector, replace it with
a new one.
When installing the airbag sensor assembly center,
be careful that the SRS wiring does not interfere with
other parts and that it is not pinched between other
parts.
After installing, shake the airbag sensor assembly to
check that there is no looseness.
1.
INSTALL AIRBAG SENSOR ASSEMBLY
(a)
Install the airbag sensor assembly with the 4 bolts.
Torque: 17.5 N·m (179 kgf·cm, 13 ft·lbf)
(b)
Connect the airbag sensor holder (with connectors).
2.
INSTALL FRONT CONSOLE BOX ASSEMBLY
(SEE PAGE
3.
INSTALL REAR CONSOLE BOX ASSEMBLY
(SEE PAGE
4.
INSTALL UPPER CONSOLE PANEL
(SEE PAGE
5.
INSTALL SHIFTING HOLE COVER
(SEE PAGE
6.
CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
7.
PERFORM INITIALIZATION (SEE PAGE
Some system need initialization when disconnecting the cable
from the negative battery terminal.
8.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст