Toyota Prius (2022 year). Manual in english — page 7
![](/vehicles/linovind/veaitilwe/hal/jot.png)
113
2
Instru
■
Main display and multi-information display
*
: The displayed indicator changes according to the current driving mode.
■
Multi-information display (symbol display
*
)
*
: These symbols are displayed along with a message. Also, the symbol dis-
plays listed here are only an example, and different symbols may be dis-
played according to the contents of the multi-information display.
Indicators and symbols displayed on the display
Indicators
Pages
EV drive mode indicator
*
“ECO MODE” indicator
*
“PWR MODE” indicator
EV Indicator
Symbol display
Pages
Smart key system
Inappropriate pedal operation
LTA (Lane Tracing Assist) (if equipped)
Low engine oil pressure warning
(Canada only)
![](/vehicles/linovind/veaitilwe/hal/pps.png)
114
■
BSM (Blind Spot Monitor) outside rear view mirror indicators
(if equipped) (
• When the BSM function is enabled on the
screen of the multi-infor-
mation display, the power switch is turned to ON mode.
If the system is functioning correctly, the BSM outside rear view mirror indi-
cators will turn off after a few seconds.
If the BSM outside rear view mirror indicators do not illuminate or do not
turn off, there may be a malfunction in the system.
If this occurs, have the vehicle inspected by your Toyota dealer.
●
Indicators are also displayed on the out-
side rear view mirrors.
●
In order to confirm operation, the BSM
outside rear view mirror indicators illumi-
nate in the following situations:
• When the power switch is in ON
mode, the BSM function is enabled
on the
screen of the multi-infor-
mation display.
WARNING
■
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the hybrid system, this could mean that these sys-
tems are not available to help protect you in an accident, which could result
in death or serious injury. Have the vehicle inspected by your Toyota dealer
immediately if this occurs.
NOTICE
■
To prevent damage to the engine and its components
The engine may be overheating if the high coolant temperature warning
light comes on or flashes. In this case, immediately stop the vehicle in a
safe place, and check the engine after it has cooled completely. (
![](/vehicles/linovind/veaitilwe/hal/oswike.png)
115
2
Instru
Main display
The units used on the display may differ depending on the target region.
The main display shows basic information, such as the vehicle
speed and remaining fuel amount. Also, the displayed informa-
tion can be switched according to user preference.
Display contents (vehicles without RSA [Road Sign Assist])
Simple screen
*
Split screen
*
*
: Refer to P. 121 for details on how to change the screen display.
![](/vehicles/linovind/veaitilwe/hal/uno.png)
116
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
Outside temperature
Displays the outside temperature within the range of -40°F (-40°C) to
122°F (50°C).
The temperature display flashes for approximately 10 seconds when the
outside temperature drops to approximately 37
F (3
C) or less, and then
stops flashing.
Mileage display (odometer/trip meters/driving range)
The possible driving range estimated from the mileage and current remain-
ing fuel amount can be displayed. (
Average fuel consumption display
The average fuel consumption that is linked with the contents of the mile-
age display can be displayed. (
Sub-screen
When split screen is selected for the main display, information such as the
Hybrid System Indicator and current fuel consumption can be displayed.
(
1
2
3
4
5
6
![](/vehicles/linovind/veaitilwe/hal/fas.png)
117
2
Instru
The units used on the display may differ depending on the target region.
Display contents (vehicles with RSA [Road Sign Assist])
![](/vehicles/linovind/veaitilwe/hal/idit.png)
118
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
Outside temperature
Displays the outside temperature within the range of -40°F (-40°C) to
122°F (50°C).
The temperature display flashes for approximately 10 seconds when the
outside temperature drops to approximately 37°F (3°C) or less, and then
stops flashing.
Mileage display (odometer/trip meters/driving range)
The possible driving range estimated from the mileage and current remain-
ing fuel amount can be displayed. (
Average fuel consumption display
The average fuel consumption that is linked with the contents of the mile-
age display can be displayed. (
Sub-screen (when RSA [Road Sign Assist] is off)
Information such as the Hybrid System Indicator and current fuel con-
sumption can be displayed. (
Sub-screen (when RSA [Road Sign Assist] is on)
Displays information related to RSA (Road Sign Assist)
*
. (
*
: When RSA (Road Sign Assist) information is displayed in the
screen
of the multi-information display (
P. 150), RSA (Road Sign Assist) infor-
mation is not displayed on the sub-screen.
1
2
3
4
5
6
7
![](/vehicles/linovind/veaitilwe/hal/ithellfly.png)
119
2
Instru
Each time
is pressed, the mileage display and fuel consumption
display change in the following order from 1 to 6.
Mileage display
Average fuel consumption dis-
play
After 1 to 6 are displayed, the dis-
plays return to 1.
Use the displayed average fuel
consumption as a reference.
Switching the mileage display and average fuel consumption
display
1
2
![](/vehicles/linovind/veaitilwe/hal/qunald.png)
120
*
1
: If
is pressed and held while this item is displayed, the information is
reset.
*
2
: This item is reset each time the hybrid system starts.
Mileage display
Average fuel consumption display
1
ODO (Odometer)
Total mileage
Average fuel consumption since
last reset
Average fuel consumption since
last reset
*
1
2
TRIP A (Trip meter A)
Mileage since last reset
*
1
TRIP A average fuel consumption
Average fuel consumption since
TRIP A was reset
*
1
3
TRIP B (Trip meter B)
Mileage since last reset
*
1
TRIP B average fuel consumption
Average fuel consumption since
TRIP B was reset
*
1
4
(Mileage since hybrid sys-
tem was started)
Mileage since hybrid system
started
*
2
Average fuel consumption after
hybrid system started
Average fuel consumption since
hybrid system was started
*
2
5
(Distance to empty)
Approximate distance vehicle
can travel based on current
remaining fuel amount
Blank screen
6
Blank screen
Blank screen
1
2
![](/vehicles/linovind/veaitilwe/hal/anthande.png)
121
2
Instru
Simple screen or split screen can be selected for the main display.
When split screen is selected, a variety of information can be displayed on
a sub-screen in addition to the contents of the simple screen.
Select the “Meter Customize” settings (
) screen on the
screen of the multi-information display, and then press
.
(
Press
or
of the meter control switches to select “Simple/
Split Screen”.
Press
to display the setting screen.
Press
or
of the meter
control switches to select a dis-
play mode.
Press
.
The contents of the main display switch to the selected display mode.
Press
to return to the previous screen.
Switching the display mode (vehicles without RSA [Road Sign
Assist])
1
2
3
4
5
![](/vehicles/linovind/veaitilwe/hal/dorute.png)
122
Vehicles without RSA (Road Sign Assist)
When split screen is selected for the main display, display contents on
the sub-screen can be selected.
Vehicles with RSA (Road Sign Assist)
When RSA is off, display contents on the sub-screen can be selected.
Press
or
of the meter
control switches and select the
sub-screen.
When the sub-screen is selected,
is displayed on the sub-
screen.
Press
or
of the meter control switches to select the display
item.
One of the following 3 items can be displayed.
Switching contents displayed on the sub-screen
1
2
Display contents
Detail
Hybrid System Indicator
A convenient Hybrid System Indicator is displayed.
Refer to P. 129 for details on how to read the Hybrid
System Indicator.
Current fuel consumption
The current fuel consumption during driving is dis-
played.
• The
mark indicates the value displayed in the
average fuel consumption display (
Switching the average fuel consumption display
also changes the position of the
mark.
• When the average fuel consumption is reset, the
position of the
mark is reset to 0.
Hybrid battery (traction battery) status
The same contents as the hybrid battery (traction
battery) status on the energy monitor are displayed.
(
![](/vehicles/linovind/veaitilwe/hal/qulane.png)
123
2
Instru
■
Outside temperature display
●
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 12 mph [20 km/h])
• When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
●
When “-” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to your Toyota dealer.
■
Distance to empty
●
This distance is computed based on your average fuel consumption. As a
result, the actual distance that can be driven may differ from that displayed.
●
When only a small amount of fuel is added to the tank, the display may not
be updated.
When refueling, turn the power switch off. If the vehicle is refueled without
turning the power switch off, the display may not be updated.
■
Switching the driving mode (
*
: The animation displayed when the driving mode is switched can be turned
off in the “Meter Customize” settings. (
When the driving mode is switched, the
driving mode indicator changes and an
animation
*
is displayed on the multi-infor-
mation display.
Also, the background color of the main
display, energy monitor (
P. 127) and
Hybrid System Indicator (
change as follows.
Driving modes
Background color
Normal mode
Green
Power mode
Red
Eco drive mode
Blue
![](/vehicles/linovind/veaitilwe/hal/dist.png)
124
Multi-information display
Information related to each icon
on the upper portion of the multi-
information display can be dis-
played by operating the meter
control switches to select the icon.
Icons are displayed when pressing
or
of the meter control
switches and turn off shortly after
pressing the switch.
Screens linked with vehicle functions may be automatically displayed
according to the operation status of the corresponding functions.
A variety of information related to the vehicle can be displayed,
including the operation status of each system and data related
to Eco driving, and the settings of each system can be changed
according to user preference.
Display contents
![](/vehicles/linovind/veaitilwe/hal/igrthutop.png)
125
2
Instru
*
1
: If equipped
*
2
: When there is a warning message that can be displayed, the color of
changes to amber.
Menu icons
Contents
Pages
Drive information
The energy monitor that shows the operation
status of the hybrid system, or other informa-
tion such as fuel consumption is displayed.
Clock setting display
The clock settings can be changed.
Navigation system-linked display
*
1
The information related to the navigation sys-
tem is displayed.
Audio system-linked display
*
1
The audio system settings can be changed.
Air conditioning system settings screen
The air conditioning system settings can be
changed.
Driving assist system information
The information related to driving assist sys-
tems such as the LTA (Lane Tracing Assist)
*
1
and dynamic radar cruise control with full-
speed range
*
1
is displayed.
Warning message display
*
2
The warning messages are displayed.
Settings display
The settings of the vehicle functions, meter
display, etc. can be changed.
![](/vehicles/linovind/veaitilwe/hal/boung.png)
126
Press
or
of the meter control switches and select the icon
of the desired item.
The selected icon is highlighted and the display switches to the information
screen.
When split screen display is selected for the main display or RSA (Road
Sign Assist)
*
is off, the sub-screen of the main display can also be
selected. (
*
: If equipped
Press
or
of the meter control switches to switch the con-
tents of the display.
Press
on screens where it
is necessary to select or con-
firm an item.
On screens with tab displays,
pressing
selects the tab dis-
play, and the screen display can be
changed by pressing
or
of
the meter control switches.
Press
to return to the previous screen.
When
is selected, the following information can be displayed by
pressing
or
of the meter control switches.
●
Energy monitor (
●
Hybrid System Indicator (
●
“Fuel Consumption Record” (
●
“Drive Monitor” (
●
“Eco Savings” (
●
“Eco-Diary” (
●
AWD display (for AWD vehicles only) (
Basic Operations
1
2
Tab display
3
Drive information
4
![](/vehicles/linovind/veaitilwe/hal/jueras.png)
127
2
Instru
◆
Energy monitor
The energy monitor can be used to check the vehicle drive status,
hybrid system operation status and energy regeneration status.
When energy is flowing, an arrow appears and a bright point of light
moves to show the direction of the flow of energy. When energy is
not flowing, the bright point of light is not displayed.
Gasoline engine
Electric motor
(traction motor)
Hybrid battery
(traction battery)
Tire
Bright point of light showing
the flow of energy
As an example, all arrows are shown in the illustration, but the actual con-
tents of the display will differ.
(Display example)
●
When the hybrid battery (traction battery) is being charged, the
bright point of light moves towards
.
●
During driving, the bright point of light moves from
or
(or
both depending on the situation) towards
.
*
●
During driving, the image of the tires rotates.
*
: The display may differ depending on the driving status.
1
2
3
4
5
3
1
2
4
![](/vehicles/linovind/veaitilwe/hal/kacheerig.png)
128
■
Hybrid battery (traction battery) status
●
The display changes in 8 levels according to the remaining charge amount
of the hybrid battery (traction battery).
●
The hybrid battery (traction battery) status is also displayed on the following
screen, but the contents of the display are the same.
• Sub-screen of the main display (
• Hybrid System Indicator (
• Head-up display (if equipped) (
●
The charge amount of the hybrid battery (traction battery) is automatically
controlled by the hybrid system. For this reason, even if electricity is recov-
ered via the regenerative braking, or electricity is generated via the gasoline
engine, the displayed hybrid battery (traction battery) charge amount may
not reach the highest level (level 8). However, this does not indicate a mal-
function.
■
Remaining charge amount warning of hybrid battery (traction battery)
●
The buzzer sounds intermittently when the hybrid battery (traction battery)
remains without charging while the shift position is in N, or the remaining
charge amount drops below a certain level.
If the remaining charge amount drops further, the buzzer sounds continu-
ously.
●
When a warning message is shown on the multi-information display and the
buzzer sounds, follow the instructions displayed on the screen to perform
troubleshooting.
Low
High
1
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст