Toyota Corolla (2020 year). Owner's manual — part 16
246
4-5. Using the driving support systems
Visually check the surroundings
and the area behind the vehicle. On
the screen, it appears that a truck is
parking at point
. However, in
reality if you back up to point
,
you will hit the truck. On the screen,
it appears that
is closest and
is farthest away. However, in reality,
the distance to
and
is the
same, and
is farther than
and
.
■
If you notice any symptoms
If you notice any of the following symptoms, refer to the likely cause
and the solution, and re-check.
If the symptom is not resolved by the solution, have the vehicle
inspected by your Toyota dealer.
Things you should know
-------------------------------------------------------------------------------------------------------------------------------------------------------------
247
4-5. Using the driving support systems
4
Dr
iv
ing
Symptom
Likely cause
Solution
The image is difficult to
see
The vehicle is in a dark
area
The temperature
around the lens is
either high or low
The outside tempera-
ture is low
There are water drop-
lets on the camera
It is raining or humid
Foreign matter (mud
etc.) is adhering to the
camera
Sunlight or headlights
are shining directly
into the camera
The vehicle is under
fluorescent lights,
sodium lights, mer-
cury lights etc.
If this happens due to
these causes, it does
not indicate a malfunc-
tion. Back up while visu-
ally checking the
vehicle’s surroundings.
(Use the monitor again
once conditions have
been improved.) The
procedure for adjusting
the picture quality of the
rear view monitor sys-
tem is the same as the
procedure for adjusting
the screen. (P.274)
The image is blurry
Dirt or foreign matter
(such as water droplets,
snow, mud etc.) is
adhering to the camera.
Flush the camera with a
large quantity of water
and wipe the camera
lens clean with a soft
and wet cloth.
The image is out of
alignment
The camera or sur-
rounding area has
received a strong
impact.
Have the vehicle
inspected by your Toy-
ota dealer.
The fixed guide lines
are very far out of
alignment
The camera position is
out of alignment.
Have the vehicle
inspected by your Toy-
ota dealer.
The vehicle is tilted
(there is a heavy load
on the vehicle, tire
pressure is low due to
a tire puncture, etc.)
The vehicle is used on
an incline.
If this happens due to
these causes, it does
not indicate a malfunc-
tion.
Back up while visually
checking the vehicle’s
surroundings.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
248
4-5. Using the driving support systems
WARNING
■
When using the rear view
monitor system
The rear view monitor system is a
supplemental device intended to
assist the driver when backing up.
When backing up, be sure to visu-
ally check all around the vehicle
both directly and using the mirrors
before proceeding. Observe the
following precautions to avoid an
accident that could result in death
or serious injuries.
●
Never depend on the rear view
monitor system entirely when
backing up. The image and the
position of the guide lines dis-
played on the screen may differ
from the actual state. Use cau-
tion, just as you would when
backing up any vehicle.
●
Be sure to back up slowly,
depressing the brake pedal to
control vehicle speed.
●
The instructions given are only
guide lines. When and how
much to turn the steering wheel
will vary according to traffic con-
ditions, road surface condi-
tions, vehicle condition, etc.
when parking. It is necessary to
be fully aware of this before
using the rear view monitor sys-
tem.
●
When parking, be sure to check
that the parking space will
accommodate your vehicle
before maneuvering into it.
●
Do not use the rear view moni-
tor system in the following
cases:
• On icy or slick road surfaces, or
in snow
• When using tire chains or emer-
gency tires
• When the trunk is not closed
completely
• On roads that are not flat or
straight, such as curves or
slopes
●
In low temperatures, the screen
may darken or the image may
become faint. The image could
distort when the vehicle is mov-
ing, or you may become unable
to see the image on the screen.
Be sure to visually check all
around the vehicle both directly
and using the mirrors before
proceeding.
●
If the tire sizes are changed, the
position of the fixed guide lines
displayed on the screen may
change.
●
The camera uses a special lens.
The distances between objects
and pedestrians that appear in
the image displayed on the
screen will differ from the actual
distances. (P.243)
NOTICE
■
How to use the camera
●
The rear view monitor system
may not operate properly in the
following cases.
• If the back of the vehicle is hit,
the position and mounting angle
of the camera may change.
• As the camera has a water
proof construction, do not
detach, disassemble or modify
it. This may cause incorrect
operation.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
249
4-5. Using the driving support systems
4
Dr
iv
ing
*
: If equipped
Each time the switch is pressed, the
system changes between sport
mode and normal mode.
1
Normal mode
Provides an optimal balance of fuel
economy, quietness, and dynamic
performance. Suitable for normal
driving.
2
Sport mode
Controls the transmission and
engine to provide quick, powerful
acceleration. This mode also
changes the steering feel, making it
suitable for when agile driving
response is desired, such as when
driving on roads with many curves.
When the sport mode is selected,
sport mode indicator comes on.
■
Automatic deactivation of sport
mode
If the engine switch is turned off
after driving in sport mode, the drive
NOTICE
• When cleaning the camera lens,
flush the camera with a large
quantity of water and wipe it
with a soft and wet cloth.
Strongly rubbing the camera
lens may cause the camera lens
to be scratched and unable to
transmit a clear image.
• Do not allow organic solvent,
car wax, window cleaner or
glass coating to adhere to the
camera. If this happens, wipe it
off as soon as possible.
• If the temperature changes rap-
idly, such as when hot water is
poured on the vehicle in cold
weather, the system may not
operate normally.
• When washing the vehicle, do
not apply intensive bursts of
water to the camera or camera
area. Doing so may result in the
camera malfunctioning.
●
Do not expose the camera to
strong impact as this could
cause a malfunction. If this hap-
pens, have the vehicle
inspected by your Toyota dealer
as soon as possible.
Driving mode select
switch
*
The driving modes can be
selected to suit driving con-
dition.
Selecting a drive mode
-------------------------------------------------------------------------------------------------------------------------------------------------------------
250
4-5. Using the driving support systems
mode will be changed to normal
mode.
■
ABS (Anti-lock Brake Sys-
tem)
Helps to prevent wheel lock
when the brakes are applied
suddenly, or if the brakes are
applied while driving on a slip-
pery road surface
■
Brake assist
Generates an increased level of
braking force after the brake
pedal is depressed when the
system detects a panic stop sit-
uation
■
VSC (Vehicle Stability Con-
trol)
Helps the driver to control skid-
ding when swerving suddenly or
turning on slippery road sur-
faces.
Driving assist systems
To keep driving safety and
performance, the following
systems operate automati-
cally in response to various
driving situations. Be
aware, however, that these
systems are supplementary
and should not be relied
upon too heavily when oper-
ating the vehicle.
Summary of the driving
assist systems
-------------------------------------------------------------------------------------------------------------------------------------------------------------
251
4-5. Using the driving support systems
4
Dr
iv
ing
■
Enhanced VSC (Enhanced
Vehicle Stability Control)
Provides cooperative control of
the ABS, TRAC, VSC and EPS.
Helps to maintain directional
stability when swerving on slip-
pery road surfaces by con-
trolling steering performance.
■
TRAC (Traction Control)
Helps to maintain drive power
and prevent the drive wheels
from spinning when starting the
vehicle or accelerating on slip-
pery roads
■
Active Cornering Assist
(ACA)
Helps to prevent the vehicle
from drifting to the outer side by
performing inner wheel brake
control when attempting to
accelerate while turning
■
Hill-start assist control
Helps to reduce the backward
movement of the vehicle when
starting on an uphill
■
EPS (Electric Power Steer-
ing)
Employs an electric motor to
reduce the amount of effort
needed to turn the steering
wheel.
■
The Secondary Collision
Brake
When the SRS airbag sensor
detects a collision and the sys-
tem operates, the brakes and
brake lights are automatically
controlled to reduce the vehicle
speed and help reduce the pos-
sibility of further damage due to
a secondary collision.
■
When the TRAC/VSC systems
are operating
The slip indicator light will flash
while the TRAC/VSC systems are
operating.
■
Disabling the TRAC system
If the vehicle gets stuck in mud, dirt
or snow, the TRAC system may
reduce power from the engine to the
wheels. Pressing
to turn the
system off may make it easier for
you to rock the vehicle in order to
free it.
To turn the TRAC system off, quickly
press and release
.
The “Traction Control Turned OFF”
will be shown on the multi-informa-
tion display.
Press
again to turn the system
back on.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
252
4-5. Using the driving support systems
■
Turning off both TRAC and VSC
systems
To turn the TRAC and VSC systems
off, press and hold
for more
than 3 seconds while the vehicle is
stopped.
The VSC OFF indicator light will
come on and the “Traction Control
Turned OFF” will be shown on the
multi-information display.
*
Press
again to turn the system
back on.
*
: PCS will also be disabled (only
Pre-Collision warning is avail-
able). The PCS warning light will
come on and a message will be
displayed on the multi-information
display. (P.194)
■
When the message is dis-
played on the multi-information
display showing that TRAC has
been disabled even if
has
not been pressed
TRAC is temporary deactivated. If
the information continues to show,
contact your Toyota dealer.
■
Operating conditions of
hill-start assist control
When the following four conditions
are met, the hill-start assist control
will operate:
●
Vehicles with continuously vari-
able transmission: The shift lever
is in a position other than P or N
(when starting off forward/back-
ward on an upward incline)
●
Vehicles with manual transmis-
sion: The shift lever is in a position
other than R when starting off for-
ward on an upward incline, or the
shift lever is in R when starting off
backward on an upward incline.
●
The vehicle is stopped
●
The accelerator pedal is not
depressed
●
The parking brake is not engaged
■
Automatic system cancelation
of hill-start assist control
The hill-start assist control will turn
off in any of the following situations:
●
Vehicles with a continuously vari-
able transmission: The shift lever
is shifted to P or N.
●
Vehicles with a manual transmis-
sion: The shift lever is shifted to R
when starting off forward on an
upward incline, or the shift lever is
shifted to other than R when start-
ing off backward on an upward
incline.
●
The accelerator pedal is
depressed
●
The parking brake is engaged
●
2 seconds at maximum elapsed
after the brake pedal is released
■
Sounds and vibrations caused
by the ABS, brake assist, VSC,
TRAC and hill-start assist con-
trol systems
●
A sound may be heard from the
engine compartment when the
brake pedal is depressed repeat-
edly, when the engine is started or
just after the vehicle begins to
move. This sound does not indi-
cate that a malfunction has
occurred in any of these systems.
●
Any of the following conditions
may occur when the above sys-
tems are operating.
None of these indicates that a
malfunction has occurred.
• Vibrations may be felt through the
vehicle body and steering.
• A motor sound may be heard also
after the vehicle comes to a stop.
• The brake pedal may pulsate
slightly after the ABS is activated.
• The brake pedal may move down
slightly after the ABS is activated.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
253
4-5. Using the driving support systems
4
Dr
iv
ing
■
Active Cornering Assist opera-
tion sounds and vibrations
When the Active Cornering Assist is
operated, operation sounds and
vibrations may be generated from
the brake system, but this is not a
malfunction.
■
EPS operation sound
When the steering wheel is oper-
ated, a motor sound (whirring
sound) may be heard. This does not
indicate a malfunction.
■
Automatic reactivation of TRAC
and VSC systems
After turning the TRAC and VSC
systems off, the systems will be
automatically re-enabled in the fol-
lowing situations:
●
When the engine switch is turned
off
●
If only the TRAC system is turned
off, the TRAC will turn on when
vehicle speed increases
If both the TRAC and VSC sys-
tems are turned off, automatic
re-enabling will not occur when
vehicle speed increases.
■
Operating conditions of Active
Cornering Assist
The system operates when the fol-
lowing occurs.
●
TRAC/VSC can operate
●
The driver is attempting to accel-
erate while turning
●
The system detects that the vehi-
cle is drifting to the outer side
●
The brake pedal is released
■
Reduced effectiveness of the
EPS system
The effectiveness of the EPS sys-
tem is reduced to prevent the sys-
tem from overheating when there is
frequent steering input over an
extended period of time. The steer-
ing wheel may feel heavy as a
result. Should this occur, refrain
from excessive steering input or
stop the vehicle and turn the engine
off. The EPS system should return
to normal within 10 minutes.
■
Secondary Collision Brake
operating conditions
The system operates when the SRS
airbag sensor detects a collision
while the vehicle is in motion.
However, the system does not oper-
ate in any of the following situations.
●
The vehicle speed is below 6 mph
(10 km/h)
●
Components are damaged
■
Secondary Collision Brake
automatic cancellation
The system is automatically can-
celed in any of the following situa-
tions.
●
The vehicle speed drops below
approximately 6 mph (10 km/h)
●
A certain amount of time elapses
during operation
●
The accelerator pedal is
depressed a large amount
WARNING
■
The ABS does not operate
effectively when
●
The limits of tire gripping perfor-
mance have been exceeded
(such as excessively worn tires
on a snow covered road).
●
The vehicle hydroplanes while
driving at high speed on wet or
slick roads.
■
Stopping distance when the
ABS is operating may exceed
that of normal conditions
The ABS is not designed to
shorten the vehicle’s stopping dis-
tance. Always maintain a safe dis-
tance from the vehicle in front of
you, especially in the following sit-
uations:
●
When driving on dirt, gravel or
snow-covered roads
-------------------------------------------------------------------------------------------------------------------------------------------------------------
254
4-5. Using the driving support systems
WARNING
●
When driving with tire chains
●
When driving over bumps in the
road
●
When driving over roads with
potholes or uneven surfaces
■
TRAC/VSC may not operate
effectively when
Directional control and power may
not be achievable while driving on
slippery road surfaces, even if the
TRAC/VSC system is operating.
Drive the vehicle carefully in con-
ditions where stability and power
may be lost.
■
Active Cornering Assist does
not operate effectively when
●
Do not overly rely on Active
Cornering Assist. Active Corner-
ing Assist may not operate
effectively when accelerating
down slopes or driving on slip-
pery road surfaces.
●
When Active Cornering Assist
frequently operates, Active Cor-
nering Assist may temporarily
stop operating to ensure proper
operation of the brakes, TRAC
and VSC.
■
Hill-start assist control does
not operate effectively when
●
Do not overly rely on hill-start
assist control. Hill-start assist
control may not operate effec-
tively on steep inclines and
roads covered with ice.
●
Unlike the parking brake,
hill-start assist control is not
intended to hold the vehicle sta-
tionary for an extended period
of time. Do not attempt to use
hill-start assist control to hold
the vehicle on an incline, as
doing so may lead to an acci-
dent.
■
When the TRAC/VSC is acti-
vated
The slip indicator light flashes.
Always drive carefully. Reckless
driving may cause an accident.
Exercise particular care when the
indicator light flashes.
■
When the TRAC/VSC systems
are turned off
Be especially careful and drive at
a speed appropriate to the road
conditions. As these are the sys-
tems to help ensure vehicle stabil-
ity and driving force, do not turn
the TRAC/VSC systems off
unless necessary.
■
Replacing tires
Make sure that all tires are of the
specified size, brand, tread pat-
tern and total load capacity. In
addition, make sure that the tires
are inflated to the recommended
tire inflation pressure level.
The ABS, TRAC and VSC sys-
tems will not function correctly if
different tires are installed on the
vehicle.
Contact your Toyota dealer for fur-
ther information when replacing
tires or wheels.
■
Handling of tires and the sus-
pension
Using tires with any kind of prob-
lem or modifying the suspension
will affect the driving assist sys-
tems, and may cause a system to
malfunction.
■
Secondary Collision Brake
Do not rely solely upon the Sec-
ondary Collision Brake. This sys-
tem is designed to help reduce
the possibility of further damage
due to a secondary collision, how-
ever, that effect changes accord-
ing to various conditions. Overly
relying on the system may result
in death or serious injury.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
255
4-6. Driving tips
4
Dr
iv
ing
4-6.Driving tips
Use fluids that are appropriate
to the prevailing outside tem-
peratures.
• Engine oil
• Engine coolant
• Washer fluid
Have a service technician
inspect the condition of the
battery.
Have the vehicle fitted with
four snow tires or purchase a
set of tire chains for the front
tires.
Ensure that all tires are the same
size and brand, and that chains
match the size of the tires.
Winter driving tips
Carry out the necessary
preparations and inspec-
tions before driving the
vehicle in winter. Always
drive the vehicle in a man-
ner appropriate to the pre-
vailing weather conditions.
Pre-winter preparations
WARNING
■
Driving with snow tires
Observe the following precautions
to reduce the risk of accidents.
Failure to do so may result in a
loss of vehicle control and cause
death or serious injury.
●
Use tires of the size specified.
●
Maintain the recommended
level of air pressure.
●
Do not drive in excess of 75
mph (120 km/h), regardless of
the type of snow tires being
used.
●
Use snow tires on all, not just
some wheels.
■
Driving with tire chains
Observe the following precautions
to reduce the risk of accidents.
Failure to do so may result in the
vehicle being unable to be driven
safely, and may cause death or
serious injury.
●
Do not drive in excess of the
speed limit specified for the tire
chains being used, or 30 mph
(50 km/h), whichever is lower.
●
Avoid driving on bumpy road
surfaces or over potholes.
●
Avoid sudden acceleration,
abrupt steering, sudden brak-
ing and shifting operations that
cause sudden engine braking.
●
Slow down sufficiently before
entering a curve to ensure that
vehicle control is maintained.
●
Do not use LTA (Lane Tracing
Assist) system. (if equipped)
●
Do not use LDA (Lane Depar-
ture Alert with steering control)
system. (if equipped)
NOTICE
■
Repairing or replacing snow
tires (vehicles with a tire pres-
sure warning system)
Request repairs or replacement of
snow tires from Toyota dealers or
legitimate tire retailers.
This is because the removal and
attachment of snow tires affects
the operation of the tire pressure
warning valves and transmitters.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
256
4-6. Driving tips
Perform the following according
to the driving conditions:
Do not try to forcibly open a
window or move a wiper that
is frozen. Pour warm water
over the frozen area to melt
the ice. Wipe away the water
immediately to prevent it from
freezing.
To ensure proper operation of
the climate control system
fan, remove any snow that
has accumulated on the air
inlet vents in front of the wind-
shield.
Check for and remove any
excess ice or snow that may
have accumulated on the
exterior lights, vehicle’s roof,
chassis, around the tires or on
the brakes.
Remove any snow or mud
from the bottom of your shoes
before getting in the vehicle.
Accelerate the vehicle slowly,
keep a safe distance between
you and the vehicle ahead, and
drive at a reduced speed suit-
able to road conditions.
Park the vehicle and shift the
shift lever to P (continuously
variable transmission), or 1 or
R (manual transmission)
without setting the parking
brake. The parking brake may
freeze up, preventing it from
being released. If the vehicle
is parked without setting the
parking brake, make sure to
block the wheels.
Failure to do so may be dan-
gerous because it may cause
the vehicle to move unexpect-
edly, possibly leading to an
accident.
Vehicles with a continuously
variable transmission: If the
vehicle is parked without set-
ting the parking brake, con-
firm that the shift lever cannot
be moved out of P
*
.
*
: The shift lever will be locked if it is
attempted to be shifted from P to
any other position without
depressing the brake pedal. If the
shift lever can be shifted from P,
there may be a problem with the
shift lock system. Have the vehi-
cle inspected by your Toyota
dealer immediately.
Use the correct tire chain size
when mounting the tire chains.
Chain size is regulated for each
tire size.
Before driving the vehicle
When driving the vehicle
When parking the vehicle
Selecting tire chains
-------------------------------------------------------------------------------------------------------------------------------------------------------------
257
4-6. Driving tips
4
Dr
iv
ing
Side chain (0.12 in. [3 mm] in
diameter)
Side chain (0.39 in. [10 mm]
in width)
Side chain (1.18 in. [30 mm]
in length)
Cross chain (0.16 in. [4 mm]
in diameter)
Cross chain (0.55 in. [14 mm]
in width)
Cross chain (0.98 in. [25 mm]
in length)
Regulations regarding the use
of tire chains vary depending on
location and type of road.
Always check local regulations
before installing chains.
■
Tire chain installation
Observe the following precautions
when installing and removing
chains:
●
Install and remove tire chains in a
safe location.
●
Install tire chains on the front tires
only. Do not install tire chains on
the rear tires.
●
Install tire chains on the front tires
as tightly as possible. Retighten
chains after driving 1/41/2 mile
(0.51.0 km).
●
Install tire chains following the
instructions provided with the tire
chains.
Regulations on the use of
tire chains
NOTICE
■
Fitting tire chains (vehicles
with a tire pressure warning
system)
The tire pressure warning valves
and transmitters may not function
correctly when tire chains are fit-
ted.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
258
4-6. Driving tips
-------------------------------------------------------------------------------------------------------------------------------------------------------------
259
5
5
Entune au
dio
Entune audio
.
5-1. Basic function
Buttons overview. . .
Menu screen . . . ...
Status icon . . . . ..
“Setup” screen . . .
5-2. Basic information before
operation
Initial screen. . . .
Touch screen. . . ...
Home screen. . . ...
Entering letters and num-
bers/list screen operation
. . . . . . . . ..
Screen adjustment . ..
Linking multi-information
display and the system
. . . . . . . . ..
5-3. Connectivity settings
Registering/Connecting a
Bluetooth
®
device . .
Setting Bluetooth
®
details
. . . . . . . . ..
Wi-Fi
®
Hotspot . . .
Apple CarPlay . . . .
5-4. Other settings
General settings. . ..
Voice settings. . . ..
Vehicle settings . . ...
5-5. Using the audio/visual
system
Quick reference. . ...
Some basics. . . .
5-6. Radio operation
AM/FM radio. . . .
Internet radio . . . ...
5-7. Media operation
USB memory. . . ...
iPod/iPhone. . . . .
Bluetooth
®
audio . . .
AUX. . . . . . . .
5-8. Audio/visual remote con-
trols
Steering switches . .
5-9. Audio settings
Setup. . . . . . ...
5-10.Tips for operating the
audio/visual system
Operating information..
5-11.Voice command system
operation
Voice command system
. . . . . . . . ..
Command list . . . ..
5-12.Mobile Assistant opera-
tion
Mobile Assistant . . ..
-------------------------------------------------------------------------------------------------------------------------------------------------------------
260
5-13.Phone operation
(Hands-free system for
cellular phones)
Quick reference. . ...
Some basics . . . ...
Placing a call using the
Bluetooth
®
hands-free sys-
tem . . . . . . .
Receiving a call using the
Bluetooth
®
hands-free sys-
tem . . . . . . .
Talking on the Bluetooth
®
hands-free system. .
Bluetooth
®
phone message
function. . . . . ..
5-14.Phone settings
Setup. . . . . . ...
5-15.What to do if... (Blue-
tooth
®
)
Troubleshooting . . ..
5-16.Toyota Entune overview
Toyota Entune . . . .
Type A: Function achieved
by using a smart phone or
DCM. . . . . . ..
Type B: Function achieved
by using DCM and the sys-
tem . . . . . . .
Type C: Function achieved
by using DCM. . .
5-17.Toyota Entune operation
Toyota Entune App Suite
Connect . . . . . .
5-18.Toyota Entune App Suite
Connect settings
Setup. . . . . . ...
-------------------------------------------------------------------------------------------------------------------------------------------------------------
261
5-1. Basic function
5
Entune au
dio
5-1.Basic function
*
: If equipped
Entune Audio Plus/Entune Premium Audio
Owners of this system should refer to the “NAVIGATION AND MUL-
TIMEDIA SYSTEM OWNER’S MANUAL”.
By touching the screen with your finger, you can control the
selected functions. (P.268, 268)
Press to seek up or down for a radio station or to access a
desired track/file. (P.307, 311, 313, 316)
Press to access the Bluetooth
®
hands-free system. (P.345)
When an Apple CarPlay connection is established, press to dis-
play the Phone app screen.
*1, 2
Press to display the Toyota Entune App Suite Connect screen.
*2,
3
Turn to change the radio station or skip to the next or previous
track/file. (P.307, 311, 313, 316)
Press to turn the audio/visual system on and off, and turn it to
Buttons overview
*
Operations of each part
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст