Nissan Murano. Manual — part 567
EC-378
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P1554 BATTERY CURRENT SENSOR
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009720122
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect battery current sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between battery current sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between battery current sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between battery current sensor harness connector and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
ECM
Voltage (V)
Connector
+
–
Terminal
Terminal
F8
42
(Battery current
sensor signal)
44
(Sensor
ground)
Above 2.3 at least once
Battery current sensor
Ground
Voltage (V)
Connector
Terminal
F76
1
Ground
Approx. 5
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F76
2
F8
44
Existed
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F76
3
F8
42
Existed
P1554 BATTERY CURRENT SENSOR
EC-379
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 5.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.
CHECK BATTERY CURRENT SENSOR
EC-379, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace battery negative cable assembly.
6.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009720123
1.
CHECK BATTERY CURRENT SENSOR
1.
Turn ignition switch OFF.
2.
Reconnect harness connectors disconnected.
3.
Disconnect battery negative cable (1).
-
: Vehicle front
-
: To body ground
4.
Install jumper cable (A) between battery negative terminal and
body ground.
5.
Turn ignition switch ON.
6.
Check the voltage between ECM harness connector terminals
under the following conditions.
Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly.
ECM
Voltage (V)
Connector
+
–
Terminal
Terminal
F8
42
(Battery current
sensor signal)
44
(Sensor ground)
Approx. 2.5
ALBIA0076ZZ
EC-380
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P1564 ASCD STEERING SWITCH
P1564 ASCD STEERING SWITCH
Description
INFOID:0000000009720124
ASCD steering switch has variant values of electrical resistance for each button. ECM reads voltage variation
of switch, and determines which button is operated.
Refer to
for the ASCD function.
DTC Logic
INFOID:0000000009720125
DTC DETECTION LOGIC
NOTE:
If DTC P1564 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 10 seconds.
2.
Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.
3.
Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
4.
Press RESUME/ACCELERATE switch for at least 10 seconds, then release it and wait at least 10 sec-
onds.
5.
Press SET/COAST switch for at least 10 seconds, then release it and wait at least 10 seconds.
6.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009720126
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK ASCD STEERING SWITCH CIRCUIT
With CONSULT
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1564
ASCD steering switch
• An excessively high voltage signal from the
ASCD steering switch is sent to ECM.
• ECM detects that input signal from the
ASCD steering switch is out of the specified
range.
• ECM detects that the ASCD steering switch
is stuck ON.
• Harness or connectors
(The switch circuit is open or shorted.)
• ASCD steering switch
• ECM
P1564 ASCD STEERING SWITCH
EC-381
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
Turn ignition switch ON.
2.
Select “MAIN SW”, “CANCEL SW”, “RESUME/ACC SW” and “SET SW” in “DATA MONITOR” mode with
CONSULT.
3.
Check each item indication under the following conditions.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector terminals under the following conditions.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 3.
3.
CHECK ASCD STEERING SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Disconnect combination switch harness connector.
4.
Check the continuity between combination switch and ECM harness connector.
5.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors M77, E105
• Combination switch (spiral cable)
• Harness for open and short between ECM and combination switch
>> Repair open circuit, short to ground or short to power in harness or connectors.
Monitor item
Condition
Indication
MAIN SW
MAIN switch
Pressed
ON
Released
OFF
CANCEL SW
CANCEL switch
Pressed
ON
Released
OFF
RESUME/ACC SW
RESUME/ACCEL-
ERATE switch
Pressed
ON
Released
OFF
SET SW
SET/COAST switch
Pressed
ON
Released
OFF
ECM
Condition
Voltage (V)
Con-
nector
+
–
Terminal
Terminal
E16
85
(ASCD steering switch
signal)
92
(ASCD steering switch
ground)
MAIN switch: Pressed
Approx. 0
CANCEL switch: Pressed
Approx. 1
SET/COAST switch: Pressed
Approx. 2
RESUME/ACCELERATE switch: Pressed
Approx. 3
All ASCD steering switches: Released
Approx. 4
Combination switch
ECM
Continuity
Terminal
Connector
Terminal
16
E16
92
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст