Nissan NV200 Taxi (2017 year). Manual — part 11

Bluetooth® streaming audio

● Some Bluetooth® audio devices may not be

recognized by the in-vehicle audio system.

● It is necessary to set up the wireless con-

nection between a compatible Bluetooth®
audio device and the in-vehicle Bluetooth®
module before using the Bluetooth® audio.

● Operating procedure of the Bluetooth® au-

dio will vary depending on the devices. Make
sure how to operate your audio device be-
fore using it with this system.

● The Bluetooth® audio may be stopped un-

der the following conditions:

● Receiving a call on the Hands-Free

Phone System.

● Checking the connection to the hands-

free phone.

● Do not place the Bluetooth® audio device in

an area surrounded by metal or far away from
the in-vehicle Bluetooth® module to prevent
tone quality degradation and wireless con-
nection disruption.

● While an audio device is connected through

the Bluetooth® wireless connection, the
battery power of the device may discharge
quicker than usual.

● This system supports the Bluetooth® Audio

Distribution Profile (A2DP, AVRCP).

BLUETOOTH® is a
trademark owned by
Bluetooth SIG, Inc.
and licensed to
Bosch.

Monitor, climate, audio, phone and voice recognition systems

4-31

FM/AM/SAT RADIO WITH
COMPACT DISC (CD) PLAYER

1.

CD eject button

2. FM-AM button

3. AUX (auxiliary) button

4. CD insert slot

5.

Backward seek button and

Forward seek button

6. BACK button

7. AUDIO button / TUNE knob

8. Display screen

9. ON-OFF button / VOL (volume) control

knob

10. CD button

11. SXM button*

*No satellite radio reception is available when the
SXM button is pressed to access satellite radio
stations unless optional satellite receiver and an-
tenna are installed and a SiriusXM® Satellite
Radio service subscription is active. Satellite ra-
dio is not available in Alaska, Hawaii and Guam.

For additional information on all operation pre-
cautions, refer to “Audio operation precautions”
in this section.

LHA2895

4-32

Monitor, climate, audio, phone and voice recognition systems

Audio main operation

ON-OFF button / VOL (volume) control
knob

Place the ignition switch in the ACC or ON
position and press the ON-OFF button while the
system is off to call up the mode (radio, CD, AUX,
Bluetooth® audio USB or iPod®) that was play-
ing immediately before the system was turned off.

To turn the system off, press the ON-OFF button.

Turn the VOL (volume) control knob to adjust the
volume.

This vehicle may be equipped with Speed Sen-
sitive Volume. When this feature is active, the
audio volume changes as the driving speed
changes.

Audio settings

1. Press the [

] button.

2. Touch the “Settings” key.

3. Touch the “Audio” key.

Use the touch-screen to adjust the following
items to the desired setting:

Audio

Bass

Adjusts the bass to the desired level.

Treble

Adjusts the treble to the desired level.

Balance

Adjusts the balance to the desired level. Balance adjusts the sound level between the left and right speakers.

Fade

Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear speakers.

Speed Sensitive Vol.

Adjusts the Speed Sensitive Volume function, which increases the volume of the audio system as the speed of the ve-
hicle increases. Set to “OFF” to disable the feature. The higher the setting, the more the volume increases in relation to
vehicle speed.

AUX Volume Level

Controls the volume level of incoming sound when an auxiliary device is connected to the system. Available options are
Low (Quiet), Medium, and High (Loud).

Bass, treble, balance and fade can also be adjusted by pressing the AUDIO button and turning the TUNE knob to select the item to adjust. When the desired
item is shown on the display, turn the tuning to adjust and then press the AUDIO button until the display returns to the main audio screen. If the button is not
pressed for approximately 10 seconds, the radio or CD display will automatically reappear.

Monitor, climate, audio, phone and voice recognition systems

4-33

Clock set

1. Press the [

] button.

2. Touch the “Settings” key.

3. Touch the “System” key.

4. Touch the “Clock” key.

5. Touch “Clock Mode” to select “Manual” to

adjust time manually.

6. Touch the “Set Clock Manually” key.

7. Touch “+” and “-” keys to adjust hour, min-

ute, day, month and year.

8. Press the BACK button to finish.

SXM settings
To view the SXM settings:

1. Press the [

] button.

2. Touch the “Settings” key.

3. Touch the “SXM” key.

The signal strength, activation status and other
information are displayed on the screen.

FM/AM/SAT radio operation

FM·AM button

Press the FM·AM button to change the band as
follows:

AM

→ FM1 → FM2 → AM

If another audio source is playing when the
FM·AM button is pressed, the audio source play-
ing will automatically be turned off and the last
radio station played will begin playing.

The FM stereo indicator (ST) is shown on the
screen during FM stereo reception. When the
stereo broadcast signal is weak, the radio auto-
matically changes from stereo to monaural re-
ception.

SXM band select

Press the SXM button to change the band as
follows:

SXM1*

→ SXM2* → SXM3* → SXM1

When the XM button is pressed while the ignition
switch is in the ACC or ON position, the radio will
come on at the station last played.

The last station played will also come on when
the ON•OFF button/ VOL (volume) control knob
is pressed ON.

*When the SXM button is pressed, the satellite
radio reception will not be available unless an
optional satellite receiver and antenna are in-
stalled and a SiriusXM® Satellite Radio service
subscription is active. Satellite radio is not avail-
able in Alaska, Hawaii and Guam.

If a compact disc is playing when the SXM button
is pressed, the compact disc will automatically be
turned off and the last radio station played will
come on.

Tuning with the touch-screen

When in AM or FM mode, the radio can be tuned
using the touch-screen. To bring up the visual
tuner, touch the “Tune” key on the lower right
corner of the screen. A screen appears with a bar
running from low frequencies on the left to high
frequencies on the right. Touch the screen at the
location of the frequency you wish to tune and the
station will change to that frequency. To return to
the regular radio display screen, touch the “OK”
key.

Tuning with the TUNE control knob

The radio can also be manually tuned using the
TUNE knob. When in FM or AM mode, turn the
TUNE knob to the left for lower frequencies or to
the right for higher frequencies. When in SXM
mode, turn the TUNE knob to change the chan-
nel.

4-34

Monitor, climate, audio, phone and voice recognition systems

SEEK tuning

When in FM or AM mode, press the seek

buttons

or

to tune from low to high

or high to low frequencies and to stop at the next
broadcasting station.
When

in

SXM

mode,

press

the

seek

buttons

or

to change the category.

1 to 6 Station memory operations
Twelve stations can be set for the FM band (6 for
FM1, 6 for FM2) and six stations can be set for
the AM band. Eighteen stations can be set for the
SXM band (6 for SXM1, 6 for SXM2 and 6 for
SXM3).

1. Choose the radio band AM, FM1 or FM2

using the FM·AM select button or choose
the radio band SXM1, SXM2 and SXM3
using the SXM button.

2. Tune to the desired station using manual or

seek tuning. Press and hold any of the de-
sired station memory buttons (1 – 6) until a
beep sound is heard.

3. The channel indicator will then come on and

the sound will resume. Programming is now
complete.

4. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected or if the fuse
opens, the radio memory will be canceled. In that
case, reset the desired stations.

Presets can also be selected by touching the
desired preset number on the screen.

LHA2899

Monitor, climate, audio, phone and voice recognition systems

4-35

Smart Favorites Preset Setup (if so
equipped)

The Smart Favorites feature allows the user to
designate presets, within the SXM1, SXM2 and
SXM3 bands, as their Smart Favorites. When any
of the Smart Favorite presets are selected, the
current track on that station will play from the
beginning of the song.

To program a Smart Favorite preset:

1. Press the SXM button.

2. Touch the “Setup” key.

3. Touch the “Tune Start” key to activate (ON)

or deactivate (OFF) Smart Favorites.

4. Touch the “Add Preset” key to select an

available preset.

For additional information, refer to “1 to 6 Station
memory operations” in this section.

NOTE:

• Smart Favorites will start functioning only
after the audio unit is turned on for a few
minutes.
• Tune Start is supported for music chan-
nels only.

Replay Screen

The Replay Screen gives the user the ability to
replay, skip, pause or rewind the currently aired
track.

When the “Replay” key is touched, the Replay
Screen is prompted.

LHA3085

LHA3087

4-36

Monitor, climate, audio, phone and voice recognition systems

REPLAY

To replay a track from
the beginning, press
the

seek button.

The user can continue
to press the

seek

button to replay previ-
ous songs, but can only
go back as far as the
system permits. The
system will warn the
user when they cannot
skip any further back by
displaying “At the End”
in the bottom left corner
of the screen.

SKIP

To skip a track, press
the

track button.

“Live” will appear in the
bottom left corner of the
screen indicating the
difference from play
time to live audio.

PAUSE

To pause a track, press
the

pause button.

REWIND/FAST
FORWARD

To rewind/ fast forward
a track, hold the
or

seek/track

button.

Compact disc (CD) player operation

If the radio is already operating, it automatically
turns off and the compact disc begins to play.

CD button

When the CD button is pressed with the system
off and the compact disc loaded, the system will
turn on and the compact disc will start to play.

When the CD button is pressed with a compact
disc loaded and the radio playing, the radio will
automatically be turned off and the compact disc
will start to play.

Monitor, climate, audio, phone and voice recognition systems

4-37

CD/MP3 display mode

Menu item

CD/MP3 display mode

While listening to a CD or an MP3/WMA CD, certain text may be displayed (when a CD encoded with text is
being used). Depending on how the CD or MP3/WMA CD is encoded, the text is displayed listing the artist,
album and song title. There are other keys displayed on the screen when a CD is playing:

Random

Touch the “Random” key to apply a random play pattern to the CD. If an MP3 CD is playing, touching “Ran-
dom” or alternates between Random Folder, and Random All. This text will appear on the display. To cancel
Random mode, touch the “Random” key until the key is no longer highlighted.

Repeat

Touch the “Repeat” key to apply a repeat play pattern to the CD. If an MP3 CD is playing, touching “Repeat”
alternates between repeating the current song and repeating the current folder. This text will appear on the
display. To cancel repeat mode, touch the “Repeat” key until the key is no longer highlighted

Browse

Touch the “Browse” key to display the titles on the CD in list format. Touch the title of a song in the list to begin
playing that song. If an MP3 CD is playing, touching the “Browse” key will also list the folders on the disc. Fol-
low the procedure for selecting a song with the touch-screen to choose a folder.

4-38

Monitor, climate, audio, phone and voice recognition systems

SEEK (Reverse or Fast

Forward) buttons

Press

and

hold

the

SEEK

buttons

or

for 1.5 seconds while the compact disc

is playing to reverse or fast forward the track
being played. The compact disc plays at an in-
creased speed while reversing or fast forwarding.
When the button is released, the compact disc
returns to normal play speed.

SEEK buttons

Press the SEEK button

while a CD or

MP3/WMA CD is playing to return to the begin-
ning of the current track. Press the SEEK
button

several times to skip backward sev-

eral tracks.

Press the SEEK button

while a CD or

MP3/WMA CD is playing to advance one track.
Press the SEEK button

several times to

skip forward several tracks. If the last track on a
CD is skipped, the first track on the disc is played.
If the last track in a folder of an MP3/WMA CD is
skipped, the first track of the next folder is played.

AUX button
The AUX IN audio input jack accepts any stan-
dard analog audio input such as from a portable
cassette tape/CD player, MP3 player or a laptop
computer. Press the AUX button to play a com-
patible device plugged into the AUX IN jack.

EJECT button

When the

button is pressed with a com-

pact disc loaded, the compact disc will eject and
the last source will be played.
If the disc is not removed within 10 seconds, the
disc will reload.

Additional features

For additional information about the iPod® player
available with this system, refer to “iPod® player
operation” in this section.

For additional information about the USB Con-
nection Port, refer to “USB (Universal Serial Bus)
Connection Port” in this section.

For additional information about the Bluetooth®
audio interface available with this system, refer to
“Bluetooth® streaming audio” in this section.

USB (Universal Serial Bus)
CONNECTION PORT

Connecting a device to the USB
connection port

WARNING

Do not connect, disconnect or operate the
USB device while driving. Doing so can be
a distraction. If distracted you could lose
control of your vehicle and cause an acci-
dent or serious injury.

LHA2584

Monitor, climate, audio, phone and voice recognition systems

4-39

CAUTION

Do not force the USB device into the

USB port. Inserting the USB device
tilted or up-side-down into the port may
damage the port. Make sure that the
USB device is connected correctly into
the USB port.

Do not grab the USB port cover (if so

equipped) when pulling the USB device
out of the port. This could damage the
port and the cover.

Do not leave the USB cable in a place

where it can be pulled unintentionally.
Pulling the cable may damage the port.

For additional information, refer to your device
manufacturer’s owner information regarding the
proper use and care of the device.

The USB connection port is located in the center
console. Insert the USB device into the connec-
tion port

1

.

When a compatible storage device is plugged
into the connection port, compatible audio files
on the storage device can be played through the
vehicle’s audio system.

Audio file operation

AUX (auxiliary) button

Place the ignition switch in the ON or ACC
position and press the AUX button to switch to
the USB input mode. If another audio source is
playing and a USB memory device is inserted,
press the AUX button until the center display
changes to the USB memory mode.

If the system has been turned off while the USB
memory was playing, press the ON-OFF button
to restart the USB memory.

Play information

Information about the audio files being played is
shown on the display screen of the vehicle’s
audio system. Touch “Browse” to display the list
of folders and files on the USB device. Touch the
name of a song on the screen to begin playing
that song.

SEEK buttons

Press the

button while an audio file on the

USB device is playing to return to the beginning
of the current track. Press the

button sev-

eral times to skip backward several tracks.

LHA2923

4-40

Monitor, climate, audio, phone and voice recognition systems

Press the

button while an audio file on the

USB device is playing to advance one track.
Press the

button several times to skip for-

ward several tracks. If the last track in a folder on
the USB device is skipped, the first track of the
next folder is played.

SEEK (Reverse or Fast

Forward) buttons

Press and hold the

or

seek buttons

for 1.5 seconds while an audio file on the USB
device is playing to reverse or fast forward the
track being played. The track plays at an in-
creased speed while reversing or fast forwarding.
When the button is released, the audio file re-
turns to normal play speed.

Random and repeat play mode
While files on a USB device are playing, the play
pattern can be altered so that songs are repeated
or played randomly.

Random
Touch the “Random” key to apply a random play
pattern to the USB device. When the random
mode is active, the

icon is displayed to the

left of the song title or album name to denote
which random pattern is applied. To cancel Ran-
dom mode, touch the “Random” key until
no

icon is displayed.

Repeat
Touch the “Repeat” key to apply a repeat play
pattern to the USB device. When the repeat
mode is active, the

icon is displayed to the

left of the song title or album name to denote
which repeat pattern is applied. To cancel repeat
mode, touch the “Repeat” key until no

icon

is displayed.

iPod®* PLAYER OPERATION

Connecting iPod®

WARNING

Do not connect, disconnect or operate the
USB device while driving. Doing so can be
a distraction. If distracted you could lose
control of your vehicle and cause an acci-
dent or serious injury.

LHA2584

Monitor, climate, audio, phone and voice recognition systems

4-41

CAUTION

Do not force the USB device into the

USB port. Inserting the USB device
tilted or up-side-down into the port may
damage the port. Make sure that the
USB device is connected correctly into
the USB port.

Do not grab the USB port cover (if so

equipped) when pulling the USB device
out of the port. This could damage the
port and the cover.

Do not leave the USB cable in a place

where it can be pulled unintentionally.
Pulling the cable may damage the port.

For additional information, refer to your device
manufacturer’s owner information regarding the
proper use and care of the device.

To connect an iPod® to the vehicle so that the
iPod® can be controlled with the audio system
controls and display screen, use the USB con-
nection port located on the center console below
the heater and air conditioner controls

1

. Con-

nect the iPod®-specific end of the cable to the
iPod® and the USB end of the cable to the USB
connection port on the vehicle. If your iPod®
supports charging via a USB connection, its bat-

tery will be charged while connected to the ve-
hicle with the ignition switch in the ACC or ON
position.

While connected to the vehicle, the iPod® can
only be operated by the vehicle audio controls.

To disconnect the iPod® from the vehicle, re-
move the USB end of the cable from the USB
connection port on the vehicle, then remove the
cable from the iPod®.

* iPod® is a trademark of Apple Inc., registered in
the U.S. and other countries.

Compatibility

The following models are compatible:

● iPod® 5th Generation (firmware version

1.2.3 or later)

● iPod® Classic (firmware version 1.1.1 or

later)

● iPod® Touch (firmware version 2.0.0 or

later)*

● iPod® nano - 1st generation (firmware ver-

sion 1.3.1 or later)

● iPod® nano - 2nd generation (firmware ver-

sion 1.1.3 or later)

● iPod® nano - 3rd generation (firmware ver-

sion 1.1.3 or later)

● iPod® nano - 4th generation (firmware ver-

sion 1.0.4 or later)

● iPod® nano - 5th generation (firmware ver-

sion 1.0.1 or later)

* Some features of this iPod® may not be fully
functional.

Make sure that your iPod® firmware is updated to
the version indicated above.

4-42

Monitor, climate, audio, phone and voice recognition systems

Audio main operation

Place the ignition switch in the ACC or ON
position. Press the AUX button repeatedly to
switch to the iPod® mode.

If the system has been turned off while the iPod®
was playing, pressing the ON·OFF button will
start the iPod®.

AUX button

When the AUX button is pressed with the system
off and the iPod® connected, the system will turn
on. If another audio source is playing and the
iPod® is connected, press the AUX button re-
peatedly until the center display changes to the
iPod® mode.

Interface

The interface for iPod® operation shown on the
vehicle’s audio system display screen is similar to
the iPod® interface. Use the touch-screen,
BACK button or the scrolling knob to navigate
the menus on the screen.

When the iPod® is playing, touch the “Menu” key
to bring up the iPod® interface.

LHA2911

LHA2907

Monitor, climate, audio, phone and voice recognition systems

4-43

Depending on the iPod® model, the following
items may be available on the menu list screen.
For additional information about each item, refer
to the iPod® Owner’s Manual.

● Playlists
● Artists
● Albums
● Genres
● Songs
● Composers
● Audiobooks
● Podcasts

Shuffle and repeat play mode

While the iPod® is playing, the play pattern can
be altered so that songs are repeated or played
randomly.

Shuffle
Touch the “Shuffle” key to apply a random play
pattern to the iPod®. When the Shuffle mode is
active, the text is illuminated. Touching the
“Shuffle” key once more will display the “Shuffle
songs” key. To cancel Shuffle mode, touch the
“Shuffle” key again until the text is no longer
illuminated.

Repeat
Touch the “Repeat” key to apply a repeat play
pattern to the iPod®. When the repeat mode is
active, the text is illuminated. Touching the “Re-
peat” key once more will display the “Repeat
song” key. To cancel Repeat mode, touch the
“Repeat” key again until the text is no longer
illuminated.

SEEK buttons

Press the SEEK button

or

to skip

backward or forward one track.

Press and hold the SEEK button

or

for 1.5 seconds while a track is playing to reverse
or fast forward the track being played. The track
plays at an increased speed while reversing or
fast forwarding. When the button is released, the
track returns to normal play speed.

Scrolling menus
While navigating long lists of artists, albums or
songs in the music menu, it is possible to scroll
the list by the first character in the name. To
activate character indexing, touch the “A-Z” key in
the upper right corner of the screen. Turn the
TUNE knob to choose the number or letter to
jump to in the list and then press the AUDIO
button.

LHA2279

4-44

Monitor, climate, audio, phone and voice recognition systems

BLUETOOTH® STREAMING AUDIO

If you have a compatible Bluetooth® audio de-
vice that is capable of playing audio files, the
device can be connected to the vehicle’s audio
system so that the audio files on the device play
through the vehicle’s speakers.

Connecting Bluetooth® audio

To connect your Bluetooth® audio device to the
vehicle, follow the procedure below:

1. Press the

button.

2. Touch the “Settings” key.

3. Touch the “Phone & Bluetooth” key.

4. Touch the “Connect New Device” key.

5. The system acknowledges the command

and asks you to initiate connecting from the
phone handset. The connecting procedure
of the cellular phone varies according to
each cellular phone model. For additional
information, refer to the cellular phone Own-
er’s

Manual.

You

can

also

visit

www.nissanusa.com/bluetooth for instruc-
tions on connecting NISSAN recommended
cellular phones.

LHA3622

LHA2844

Monitor, climate, audio, phone and voice recognition systems

4-45

Audio main operation

To switch to the Bluetooth® audio mode, press
the AUX button repeatedly until the Bluetooth®
audio mode is displayed on the screen.

The controls for the Bluetooth® audio are dis-
played on the screen.

CD CARE AND CLEANING

● Handle a CD by its edges. Do not bend the

disc. Never touch the surface of the disc.

● Always place the discs in the storage case

when they are not being used.

● To clean a disc, wipe the surface from the

center to the outer edge using a clean, soft
cloth. Do not wipe the disc using a circular
motion.

● Do not use a conventional record cleaner or

alcohol intended for industrial use.

● A new disc may be rough on the inner and

outer edges. Remove the rough edges by
rubbing the inner and outer edges with the
side of a pen or pencil as illustrated.

LHA0049

4-46

Monitor, climate, audio, phone and voice recognition systems

Была ли эта страница вам полезна?
Да!Нет
6 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности