Nissan Murano Z51. Instruction — part 457
DLK-336
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR HINGE : Removal and Installation
INFOID:0000000005517802
REMOVAL
1.
Remove back door assembly. Refer to
DLK-331, "BACK DOOR ASSEMBLY : Removal and Installation"
2.
Remove luggage side finisher lower and luggage side finisher upper. Refer to
.
3.
Using a remover tool, remove headlining clip at the rear side of headlining. Refer to
(NORMAL ROOF),
INT-30, "SUNROOF : Exploded View"
(SUNROOF).
4.
Remove rear side of headlining.
5.
Remove power back door drive assembly. Refer to
DLK-354, "POWER BACK DOOR DRIVE ASSEMBLY
.
6.
Remove back door hinge mounting nuts (body side), and then remove back door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close operation after installation.
• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing back door assembly, perform the fitting adjustment. Refer to
"BACK DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
BACK DOOR STAY
BACK DOOR STAY : Exploded View
INFOID:0000000005517803
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
JMKIA3496ZZ
BACK DOOR
DLK-337
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR STAY : Removal and Installation
INFOID:0000000005517804
REMOVAL
1.
Support back door assembly with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding back door open when removing back door
stay.
2.
Remove mounting bolts of back door stay (body side).
3.
Remove metal clip (3) located on the connection between the
back door stay (1) and the stud ball (2) (back door side), by
using a flat-bladed screwdriver (A).
4.
Disengage and remove back door stay from stud ball (back door
side).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check back door open/close operation after installation.
BACK DOOR STAY : Disposal
INFOID:0000000005517805
1.
Fix back door stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the back door stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on back door stay, always cover a
hacksaw using a shop cloth (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
BACK DOOR WEATHER-STRIP
: Vehicle front
Refer to
for symbols in the figure.
JMKIA2255ZZ
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
DLK-338
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR WEATHER-STRIP : Exploded View
INFOID:0000000005517806
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000005517807
REMOVAL
1.
Remove mounting bolts of power back door drive assembly (1)
(back door side).
2.
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1.
Working from the upper section, align weather-strip center mark (A) with vehicle center mark (cutting posi-
tion) and install weather-strip onto the vehicle.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
JMKIA1918ZZ
BACK DOOR
DLK-339
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
For the lower section, align weather-strip seam with center of back door striker.
3.
Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Make sure that weather-strip is fit tightly at each corner and luggage rear plate.
4.
Install mounting bolts of power back door drive assembly (back door side).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст