Nissan Sentra. Instruction — part 268
DLK-188
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
2. Disconnect the harness connector (B) and emergency release
handle (2) from the trunk lid lock (1).
3. Remove the trunk lid lock bolts (A) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform the trunk lid assembly adjustment procedure. Refer to
.
EMERGENCY LEVER
EMERGENCY LEVER : Removal and Installation
INFOID:0000000009756500
REMOVAL
1. Remove the trunk lid finisher (if equipped). Refer to
INT-45, "Removal and Installation"
.
2. Using a suitable tool release the pawls and remove emergency
release handle (1) from trunk lid assembly.
: Pawl
3. Disconnect emergency release handle cable (2) from trunk lid
lock assembly (3).
INSTALLATION
Installation is in the reverse order of removal.
TRUNK LID STRIKER
TRUNK LID STRIKER : Removal and Installation
INFOID:0000000009756501
REMOVAL
1. Remove the trunk kicking plate. Refer to
INT-42, "TRUNK REAR PLATE : Removal and Installation"
.
2. Remove bolts (A) and striker (1).
INSTALLATION
ALKIA2736ZZ
ALKIA2310ZZ
ALKIA2737ZZ
TRUNK LID
DLK-189
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Installation is in the reverse order of removal.
CAUTION:
After installation, perform the trunk lid assembly adjustment procedure. Refer to
.
DLK-190
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000009756502
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000009756503
REMOVAL
1. Fully open fuel filler lid.
2. Remove fuel cap clip (A).
1.
Fuel filler lid
2.
Bumper rubber
3.
Fuel filler lid opener cable
4.
Fuel filler lid lock
A. Clip
B. Bolt
C. Cable protector
ALKIA2919ZZ
ALKIA2921ZZ
FUEL FILLER LID OPENER
DLK-191
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
NOTE:
• The following table shows the specifications for a correctly installed fuel filler lid.
• Fitting adjustment cannot be performed.
Unit: mm (in)
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000009756504
REMOVAL
1. Remove hood and fuel filler handle assembly bolts (A).
2. Release fuel filler lid opener cable (2) by pulling downward and
then sliding cable end to the side to remove from hood and fuel
filler handle assembly (1).
3. Remove dash side finisher (LH). Refer to
IP-14, "Removal and Installation"
4. Remove center pillar lower finisher (LH). Refer to
INT-27, "CENTER PILLAR LOWER FINISHER :
.
ALKIA2929ZZ
Portion
Measurement
Standard
Fuel filler lid – Body side outer
Clearance
5.1
±1.0 (0.20 ±0.04)
Fuel filler lid – Body side outer
Surface height
0.0
±1.0 (0.0 ±0.04)
JMKIA7998ZZ
JMKIA7999ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст