Nissan Sentra. Instruction — part 425
EC-396
< DTC/CIRCUIT DIAGNOSIS >
[MRA8DE]
P1572 ASCD BRAKE SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
P1574 ASCD VEHICLE SPEED SENSOR
EC-397
< DTC/CIRCUIT DIAGNOSIS >
[MRA8DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1574 ASCD VEHICLE SPEED SENSOR
Description
INFOID:0000000009758650
The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combina-
tion meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD
control. Refer to
EC-51, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description"
functions.
DTC Logic
INFOID:0000000009758651
DTC DETECTION LOGIC
NOTE:
• If DTC P1574 is displayed with DTC U1001, first perform the trouble diagnosis for DTC U1001. Refer
.
• If DTC P1574 is displayed with DTC P0500, first perform the trouble diagnosis for DTC P0500. Refer
EC-330, "EXCEPT FOR M/T MODELS : DTC Logic"
• If DTC P1574 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer
.
• If DTC P1574 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine.
2. Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
3. Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009758652
1.
CHECK DTC WITH TCM
Check DTC with TCM. Refer to
.
Is DTC detected?
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P1574
ASCD VHL SPD SEN
(ASCD VHL SPD SEN)
ECM detects a difference between two
vehicle speed signals is out of the speci-
fied range.
• Harness or connectors
(CAN communication line is open or shorted.)
• ABS actuator and electric unit (control unit)
• TCM
• ECM
EC-398
< DTC/CIRCUIT DIAGNOSIS >
[MRA8DE]
P1574 ASCD VEHICLE SPEED SENSOR
NO
>> GO TO 2.
YES
>> Perform trouble shooting relevant to DTC indicated.
2.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check DTC with ABS actuator and electric unit (control unit). Refer to
BRC-31, "CONSULT Function (ABS)"
Is DTC detected?
NO
>> INSPECTION END
YES
>> Perform trouble shooting relevant to DTC indicated.
P1650 STARTER MOTOR RELAY 2
EC-399
< DTC/CIRCUIT DIAGNOSIS >
[MRA8DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1650 STARTER MOTOR RELAY 2
Description
INFOID:0000000009758653
ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits
a control signal to IPDM E/R via BCM by CAN communication.
Under normal conditions, ECM controls and maintains the starter relay in OFF state during following condition:
• Engine is running.
• Selector lever is D position.
When detecting a decrease in engine speed due to rapid deceleration or heavy load condition, ECM controls
and reactivates the starter relay.
IPDM E/R detects a control state of starter relay and starter control relay and transmits a feedback signal to
ECM via CAN communication.
DTC Logic
INFOID:0000000009758654
DTC DETECTION LOGIC
NOTE:
• If DTC P1650 is displayed with DTC U1001, perform the trouble diagnosis for DTC U1001. Refer to
.
• If DTC P1650 is displayed with DTC P0607, perform the trouble diagnosis for DTC P0607. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND C
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
DTC No.
CONSULT screen terms
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P1650
STR MTR RELAY 2
(Starter motor relay 2)
A
Starter relay is stuck ON.
• Harness and connectors
(Between IPDM E/R harness connector and
BCM harness connector is shorted to ground.)
• IPDM E/R
B
Starter relay power supply circuit is
excessively high voltage.
• Harness and connectors
(Between IPDM E/R harness connector and
BCM harness is open or shorted to power.)
(Between IPDM E/R harness connector and bat-
tery is open.)
• IPDM E/R
C
Starter relay circuit is excessively
low voltage
• Harness and connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст