Nissan Qashqai (2007-2010). Manual — part 1213
SEC-52
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
STOP LAMP
STOP LAMP
Description
INFOID:0000000001096712
Stop lamp switch detects that brake pedal is depressed, and then transmits the signal to BCM.
Component Function Check
INFOID:0000000001096713
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
Check stop lamp function by depressing brake pedal.
Is the inspection result normal?
YES
>> Stop lamp switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000001096714
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Disconnect stop lamp switch connector.
2.
Check voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK STOP LAMP SWITCH SIGNAL CIRCUIT
1.
Check continuity between BCM harness connector and stop lamp switch connector.
2.
Check continuity between stop lamp switch connector and ground.
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M66
51
Ground
Brake pedal is depressed
Battery voltage
Brake pedal is not depressed
0
Terminals
Voltage (V)
(Approx.)
(+)
(–)
Stop lamp switch connector
Terminal
E114 (with gasoline engine and M/
T models)
E115 (except gasoline engine and
M/T models)
1
Ground
Battery voltage
BCM connector
Terminal
Stop lamp switch connector
Terminal
Continuity
M66
51
E114 (with gasoline engine
and M/T models)
E115 (except gasoline en-
gine and M/T models)
2
Existed
STOP LAMP
SEC-53
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK STOP LAMP SWITCH
Check stop lamp switch function.
Refer to
SEC-49, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace stop lamp switch.
Component Inspection
INFOID:0000000001096715
1.
CHECK STOP LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch harness connector.
3.
Check continuity between stop lamp switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace stop lamp switch.
Stop lamp switch connector
Terminal
Ground
Continuity
E114 (with gasoline engine and M/T models)
E115 (except gasoline engine and M/T models)
2
Ground
Not existed
Stop lamp switch
Condition
Continuity
Connector
Terminal
E114 (with gasoline engine and
M/T models)
E115 (except gasoline engine
and M/T models)
1
2
Brake pedal is depressed
Existed
Brake pedal is released
Not existed
SEC-54
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HOOD SWITCH
HOOD SWITCH
Description
INFOID:0000000000944671
Hood switch detects that hood is open/close condition, and then transmits the signal to IPDM E/R.
Component Function Check
INFOID:0000000000944672
1.
CHECK FUNCTION
1.
Select “HOOD SW” in “Data Monitor” mode with CONSULT-III.
2.
Check the hood switch signal under the following condition.
Is the indication normal?
YES
>> INSPECTION END.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000000944673
1.
CHECK HOOD SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK HOOD SWITCH SIGNAL CIRCUIT
1.
Disconnect IPDM E/R and hood switch connector.
2.
Check continuity between IPDM E/R harness connector and hood switch harness connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HOOD SWITCH GROUND CIRCUIT
Check continuity between hood switch harness connector and ground.
Test item
Condition
Status
HOOD SW
Hood
Open
ON
Close
OFF
IPDM E/R
Ground
Condition
Voltage (V)
(Approx.)
Connector
Terminal
E12
21
Ground
Hood
Open
0
Close
Battery voltage
IPDM E/R
Hood switch
Continuity
Connector
Terminal
Connector
Terminal
E12
21
E113
2
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E12
21
Ground
Not existed
HOOD SWITCH
SEC-55
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK IPDM E/R OUTPUT
1.
Connect the IPDM E/R connector.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R. Refer to
PCS-32, "Removal and Installation"
.
5.
CHECK HOOD SWITCH
SEC-55, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace hood switch.
6.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-32, "Removal and Installation"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000000944674
1.
CHECK HOOD SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check continuity between hood switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hood switch.
Hood switch
Ground
Continuity
Connector
Terminal
E113
1
Ground
Existed
IPDM E/R
Ground
Voltage (V)
(Approx.)
Connector
Terminal
E12
21
Ground
Battery voltage
Hood switch
Condition
Continuity
Terminal
1
2
Hood switch
Push
Not existed
Release
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст