Nissan Qashqai (2007-2010). Manual — part 1214
![](/vehicle/qul/ene/roryboritele/myer.png)
SEC-56
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HORN
HORN
Description
INFOID:0000000000944675
Horn is located inside of front bumper and operates when theft warning system is in alarm phase.
Component Function Check
INFOID:0000000000944676
1.
CHECK FUNCTION
1.
Select “HORN” in “ACTIVE TEST” mode with CONSULT-III.
2.
Check the horn operation.
Is the operation normal?
YES
>> INSPECTION END.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000000944677
1.
CHECK HORN FUNCTION
Check horn function with horn switch.
Does the horn sound?
YES
>> GO TO 2.
NO
>> Refer to
HRN-2, "Wiring Diagram - HORN -"
.
2.
CHECK HORN RELAY POWER SUPPLY
1.
Turn ignition switch ON.
2.
Perform “ACTIVE TEST” (“HORN”) with CONSULT-Ill.
3.
Check voltage between horn relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK HORN RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R and horn relay 1and 2 connector.
3.
Check continuity between IPDM E/R harness connector and horn relay 1and 2 harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
Horn relay
Ground
Test item
Voltage (V)
(Applox.)
Connector
Terminal
E5
2
Ground
HORN
ON
→
Battery voltage
→
0
→
Battery voltage
Other than above
0
IPDM E/R
Horn relay 1 and 2
Continuity
Connector
Terminal
Connector
Terminal
E12
30
E5
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E12
30
Ground
Not existed
HORN
SEC-57
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R.Refer to
PCS-32, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
![](/vehicle/qul/ene/roryboritele/kngasi.png)
SEC-58
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY INDICATOR
VEHICLE SECURITY INDICATOR
Description
INFOID:0000000000944681
• Vehicle security indicator is built in combination meter.
• NATS (Nissan Anti-Theft System) and vehicle security system conditions are indicated by blink or illumina-
tion of vehicle security indicator.
Component Function Check
INFOID:0000000000944682
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in the “ACTIVE TEST” mode with CONSULT-III.
2.
Check vehicle security indicator operation.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000001098043
1.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK SECURITY INDICATOR LAMP SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and combination meter connector.
3.
Check continuity between combination meter connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM FUNCTION
1.
Connect combination meter connector.
2.
Check voltage between BCM harness connector and ground.
Test item
Description
THEFT IND
ON
Vehicle security indicator
ON
OFF
OFF
Terminals
Voltage (V)
(Approx.)
(+)
(–)
Combination meter connector
Terminal
M34
1
Ground
Battery voltage
BCM connector
Terminal
Combination meter connector
Terminal
Continuity
M65
18
M34
28
Existed
Combination meter connector
Terminal
Ground
Continuity
M34
28
Ground
Not existed
![](/vehicle/qul/ene/roryboritele/eldbyoha.png)
VEHICLE SECURITY INDICATOR
SEC-59
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace combination meter. Refer to
MWI-72, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-64, "Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
Terminals
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M65
18
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст