Nissan Qashqai (2007-2010). Manual — part 636
![](/vehicle/qul/ene/roryboritele/exitr.png)
PREPARATION
DLN-117
< PREPARATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Commercial Service Tools
INFOID:0000000000972162
KV38108500
Drive pinion socket
• Removing and installing drive pinion nut
• Measuring preload torque
ST33230000
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.
Installing pinion front bearing outer race
ST23860000
Drift
a: 38 mm (1.50 in) dia.
b: 33 mm (1.30 in) dia.
• Installing pinion rear bearing inner race
• Installing pinion front bearing inner race
ST3127S000
Preload gauge
Measuring preload torque
KV389L0010
Dummy cover set
• Checking backlash
• Checking drive gear runout
• Checking tooth contact
Tool number
Tool name
Description
ZZA1205D
ZZA1046D
ZZA0534D
ZZA0503D
PDIA0894E
Tool name
Description
Flange wrench
Removing and installing companion flange
lock nut
NT771
![](/vehicle/qul/ene/roryboritele/kerohor.png)
DLN-118
< PREPARATION >
[REAR FINAL DRIVE: R145]
PREPARATION
Drift
a: 54.5 mm (2.146 in) dia.
Removing and installing gear carrier and rear
cover (2 pieces are used)
Pin punch
a: 4.5 mm (0.177 in) dia.
Removing and installing lock pin
Drift
a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
Installing side bearing inner race
Drift
a: 62 mm (2.44 in) dia.
Installing pinion front bearing inner race
Stand
Installing pinion front bearing inner race
PDIA0893E
NT410
ZZA0936D
NT109
ZZA1050D
![](/vehicle/qul/ene/roryboritele/ing.png)
REAR FINAL DRIVE ASSEMBLY
DLN-119
< FUNCTION DIAGNOSIS >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
FUNCTION DIAGNOSIS
REAR FINAL DRIVE ASSEMBLY
System Diagram
INFOID:0000000000972163
1.
Coupling front bearing
2.
Pinion front bearing
3.
Pinion rear bearing
4.
Side gear
5.
Drive gear
6.
Pinion mate gear
7.
Pinion mate shaft
8.
Differential case
9.
Side bearing
10. Drive pinion
11.
Collapsible spacer
12. Electric controlled coupling
13. Companion flange
JSDIA0264ZZ
![](/vehicle/qul/ene/roryboritele/ckum.png)
DLN-120
< ON-VEHICLE MAINTENANCE >
[REAR FINAL DRIVE: R145]
REAR DIFFERENTIAL GEAR OIL
ON-VEHICLE MAINTENANCE
REAR DIFFERENTIAL GEAR OIL
Inspection
INFOID:0000000000972164
OIL LEAKEGE
Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a new gasket on filler plug and install it on final drive assembly.
CAUTION:
Never reuse gasket.
Draining
INFOID:0000000000972165
1.
Stop engine.
2.
Remove drain plug (1) and drain gear oil.
3.
Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000000972166
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a new gasket to filler plug,
then install it to final drive assembly. Refer to
CAUTION:
Never reuse gasket.
JSDIA0198ZZ
JSDIA0197ZZ
Oil grade and Viscosity
: Refer to
.
Oil capacity
: Refer to
JSDIA0198ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст