Nissan Qashqai (2007-2010). Manual — part 660

FAX-62

< ON-VEHICLE REPAIR >

[4WD]

FRONT DRIVE SHAFT

2.

Press support bearing onto housing.

3.

Install snap ring.

CAUTION:

Never reuse snap ring.

4.

Install dust shields.

CAUTION:

Never reuse dust shields.

Dynamic Damper

Secure dynamic damper with bands in the following specified posi-
tion when removing.

CAUTION:

Never reuse bands.

Wheel Side

For further details, refer to the installation procedure of “

FAX-51, "Replacement"

” for the drive shaft boot.

Inspection

INFOID:0000000001080628

INSPECTION AFTER REMOVAL

• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-

cant looseness.

• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there

is a non-standard condition.

YAX007

YAX008

Standard

Demission :

FAX-64, "Drive Shaft"

.

FAC0156D

SDIA1190J

FRONT DRIVE SHAFT

FAX-63

< ON-VEHICLE REPAIR >

[4WD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

INSPECTION AFTER DISASSEMBLY

Shaft

Check shaft for runout, cracks, or other damage. Replace if there are.

Joint Sub-Assembly (Wheel Side)

Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.

Housing and Spider assembly (Transaxle Side)

Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.

Dynamic Damper (Right Side)

Check damper for cracks or wear. Replace as necessary.

Support Bearing (Right Side)

Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.

Support Bearing Bracket (Right Side)

Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.

FAX-64

< SERVICE DATA AND SPECIFICATIONS (SDS)

[4WD]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000001080633

Drive Shaft

INFOID:0000000001080634

M/T MODELS

CVT MODELS

Axial end play

0.05 mm (0.002 in) or less

Joint

Wheel side

Transaxle assembly side

Grease quantity

Left side

115 – 135 g (4.06 – 4.76 oz)

200 – 220 g (7.05 – 7.76 oz)

Right side

Boots installed length (L)

Left side

133.5 mm (5.26 in)

189.6 mm (7.46 in)

Right side

177.6 mm (6.99 in)

Dynamic damper

A

B

Dimension

Right side

219 – 223 mm (8.62 – 8.78 in)

70 mm (2.76 in)

JPDIF0031ZZ

FAC0156D

Joint

Wheel side

Transaxle assembly side

Grease quantity

Left side

115 – 135 g (4.06 – 4.76 oz)

200 – 220 g (7.05 – 7.76 oz)

Right side

SERVICE DATA AND SPECIFICATIONS (SDS)

FAX-65

< SERVICE DATA AND SPECIFICATIONS (SDS)

[4WD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

Boots installed length (L)

Left side

133.5 mm (5.26 in)

185.6 mm (7.31 in)

Right side

177.6 mm (6.99 in)

Dynamic damper

A

B

Dimension

Right side

239 – 242 mm (9.41 – 9.53 in)

70 mm (2.76 in)

JPDIF0031ZZ

FAC0156D