Nissan Qashqai (2007-2010). Manual — part 1483
BCS-22
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
MULTIREMOTE ENT
MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)
INFOID:0000000001097017
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Test item
Operation
Description
INT LAMP
ON
Outputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, personal lamp, room lamp, luggage room lamp (when applicable lamps
switch is in DOOR position.)]
OFF
Stops the interior room lamp control signal to turn the interior room lamps.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor Item
Condition
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
KEYKESS LOCK
Indicates [ON/OFF] condition of lock signal from key fob.
KEYLESS UNLOCK
Indicates [ON/OFF] condition of unlock signal from key fob.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
RKE LOCK AND UNLOCK
This item is indicated, but not monitored.
Test item
Description
DOOR LOCK
This test is able to check warning chime in combination meter operation. [ALL LOCK/ALL UN-
LOCK/DR UNLOCK/OTHER UNLOCK]
INT LAMP
This test is able to check interior lamp operation [ON/OFF].
FLASHER
This test is able to check flasher operation [LH/RH/OFF].
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000001097018
WORK SUPPORT
*: Initial setting
DATA MONITOR
Test item
Description
HAZARD LAMP SET
Answer back function (hazard) mode can be changed in this mode.
For the detail of the setting, refer to
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 2 minutes
• MODE 3: 3 minutes
• MODE 4: 4 minutes
• MODE 5: 5 minutes
Service item
Setting item
Setting
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time.
MODE 2
*
30 sec.
Monitor item
[Unit]
Description
IGN ON SW
[ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC SW
[ON/OFF]
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
HI BEAM SW
[ON/OFF]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW1
[ON/OFF]
HEAD LAMP SW2
[ON/OFF]
TAIL LAMP SW
[ON/OFF]
AUTO LIGHT SW
[ON/OFF]
PASSING SW
[ON/OFF]
FR FOG SW
[ON/OFF]
RR FOG SW
[ON/OFF]
DOOR SW-DR
[ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS
[ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL
[ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW
[ON/OFF]
The switch status input from back door switch
BCS-24
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
INFOID:0000000001097019
WORK SUPPORT
*:Factory setting
DATA MONITOR
TURN SIGNAL R
[ON/OFF]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[ON/OFF]
ENGINE RUNNING
[ON/OFF]
The engine status received from ECM with CAN communication
PUSH SW
[ON/OFF]
Push switch status received from Intelligent Key unit by CAN communication
LIT-SEN FAIL
[OK/NOTOK]
• The sensor status received from light & rain sensor with serial link
• The serial link condition that BCM judges
AUT LIGHT SYS
[ON/OFF]
Auto light system status that BCM judges from the vehicle condition
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
RR FOG LAMP
ON
• Outputs the voltage to turn the rear fog lamp ON.
• Transmits the rear fog lamp status signal to the combination meter with
CAN communication to turn the rear fog lamp indicator lamp ON.
OFF
• Stops the voltage to turn the rear fog lamp OFF.
• Stops the rear fog lamp status signal transmission.
DAYTIME RUNNING LIGHT
ON
Transmits the day time running light request signal to IPDM E/R with
CAN communication to turn the each lamps ON.
OFF
Stops the day time running light request signal transmission.
Service item
Setting
item
Description
WIPER SPEED
SETTING
ON*
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFF
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000001097020
DATA MONITOR
Monitor Item
[Unit]
Description
IGN ON SW
Ignition switch ON status judged from ignition power supply.
IGN SW CAN
Ignition switch ON status received from IPDM E/R with CAN communication.
FR WIPER HI
[OFF/ON]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW
[OFF/ON]
FR WIPER INT
[OFF/ON]
FR WASHER SW
[OFF/ON]
H/L WASH SW
[OFF/ON]
NOTE:
The item is indicated, but not monitored.
INT VOLUME
[1
−
7]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER STOP
[OFF/ON]
Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion.
VEHICLE SPEED
[km/h]
The value of the vehicle speed signal received from combination meter with CAN com-
munication.
RR WIPER ON
[OFF/ON]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT
[OFF/ON]
RR WASHER SW
[OFF/ON]
RR WIPER STOP
[OFF/ON]
Rear wiper motor (stop position) status input from the rear wiper motor.
Test item
Operation
Description
FR WIPER
HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
ON
Outputs the voltage to operate the rear wiper motor.
OFF
Stops the voltage to stop.
HEADLAMP WASH-
ER
ON
Transmits the headlamp washer request signal to IPDM E/R with CAN communication to
operate the headlamp washer operation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст