Nissan Qashqai (2007-2010). Manual — part 1189
![](/vehicle/qul/ene/roryboritele/ayop.png)
RADIATOR CORE SUPPORT
DLK-835
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000001098717
1.
Energy absorber
2.
Bumper reinforcement
3.
Hood lock support stay
4.
Intercooler bracket
(with K9K engine models)
5.
Radiator core support assembly
6.
Upper air dam
7.
Apron bracket assembly
8.
Fastener
9.
Energy absorber lower
10. Front air guide lower
11.
Horn assembly
12. Front air guide side lower RH
13. Front air guide side RH
14. Front air guide side LH
15. Front air guide side lower LH
16. Oil cooler bracket upper
17. Oil cooler bracket lower
18. Oil cooler bracket side
JMKIA0172ZZ
![](/vehicle/qul/ene/roryboritele/tenong.png)
DLK-836
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
RADIATOR CORE SUPPORT
Removal and Installation
INFOID:0000000001098718
REMOVAL
1.
Remove the front fillet molding. Refer to
EXT-23, "Removal and Installation"
2.
Remove the front bumper fascia and the energy absorber. Refer to
EXT-11, "Removal and Installation"
3.
Remove the energy absorber (upper and lower). Refer to
EXT-11, "Removal and Installation"
.
4.
Remove the air cleaner duct. Refer to
EM-27, "Removal and Installation"
.
5.
Remove the front combination lamp (LH/RH). Refer to
EXL-171, "Removal and Installation"
.
6.
Remove the bumper reinforcement. Refer to
EXT-11, "Removal and Installation"
.
7.
Disconnect the hood lock control cable clamp, and then remove the hood lock assembly. Refer to
833, "HOOD LOCK CONTROL : Removal and Installation"
.
8.
Remove the air guide mounting clips, and then remove the air guide (LH/RH).
9.
Remove the hood lock stay mounting bolts, and then remove the hood lock stay.
10. Remove the hood switch (with theft warning systems). Refer to SEC-
SEC-156, "Removal and Installa-
11. Remove the crush zone sensor. Refer to
SR-14, "Removal and Installation"
.
12. Remove the horn. Refer to
HRN-5, "Removal and Installation"
13. Remove the ambient sensor. Refer to
VTL-22, "Removal and Installation"
14. Remove the radiator mounting bracket (LH/RH). Refer to
CO-13, "Removal and Installation"
15. Remove the Intelligent Key warning buzzer (with Intelligent Key systems). Refer to
16. Remove the charge air cooler assembly (with K9K engine models). Refer to
.
17. Remove the A/T fluid cooler assembly and the A/T fluid cooler bracket (with A/T models only). Refer to
TM-348, "FLUID COOLER : Removal and Installation"
18. Remove the A/T fluid cooler pipe bracket (1) mounting bolts (A)
(with A/T models only).
19. Remove the washer tank. Refer to
WW-99, "Removal and Installation"
.
20. Use the baby crane (A) or another piece of equipment to suspend the radiator (1) and condenser (2).
JMKIA0173ZZ
JMKIA0174ZZ
RADIATOR CORE SUPPORT
DLK-837
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
21. Remove the radiator core support assembly mounting bolts, and draw out the radiator core support
assembly to the front of the vehicle.
22. Remove the radiator core support assembly.
23. Remove the following parts after removing the radiator core support assembly.
• Inlet tube bracket (with K9K engine models)
• Intercooler bracket (with K9K engine models)
• Apron reinforcement bracket
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installation, refill the following parts.
• A/T fluid. Refer to
.
• Engine coolant. Refer to
![](/vehicle/qul/ene/roryboritele/jecherond.png)
DLK-838
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000001098719
Removal and Installation
INFOID:0000000001098720
REMOVAL
1.
Remove the outer fender protector. Refer to
EXT-22, "Removal and Installation"
.
2.
Remove the inner fender protector. Refer to
EXT-22, "Removal and Installation"
.
3.
Remove the side turn signal lamp. Refer to
EXL-178, "Removal and Installation"
4.
Remove the front bumper fascia. Refer to
EXT-11, "Removal and Installation"
.
5.
Remove the front combination lamp.
• XENON TYPE:
EXL-171, "Removal and Installation"
.
• HALOGEN TYPE:
EXL-327, "Removal and Installation"
.
6.
Remove the mounting clips and remove hoodledge cover.
7.
Remove the center mudguard. Refer to
EXT-28, "Removal and Installation"
1.
Hood seal assembly (side)
2.
Front fender finisher
3.
Front fender seal
4.
Front fender
: Metal clip
JMKIA0177ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст