Nissan Qashqai (2007-2010). Manual — part 2004
CHASSIS MAINTENANCE
MA-55
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Check exhaust pipes, muffler and mounting for improper attachment,
leaks, cracks, damage, chafing or deterioration.
• If anything is found, repair or replace damaged parts.
CVT FLUID
CVT FLUID : Inspection
INFOID:0000000001115874
CHECKING CVT FLUID
Fluid level should be checked with the fluid warmed up to 50 to 80
°
C (122 to 176
°
F). The fluid level check pro-
cedure is as follows:
1.
Check for fluid leakage.
2.
With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20
°
C (68
°
F), it takes about 10
minutes for the CVT fluid to warm up to 50 to 80
°
C (122 to
176
°
F).
3.
Park the vehicle on a level surface.
4.
Apply parking brake firmly.
5.
With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.
6.
Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.
7.
Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180
°
from the originally installed position,
then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.
CAUTION:
When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.
SMA211A
SMA146B
SCIA1933E
SCIA1931E
MA-56
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
8.
Place the selector lever in “P” or “N” and make sure the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until securely locked.
CVT FLUID CONDITION
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of CVT.
Flush cooling system after repair of CVT.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of CVT. Refer to
.
CVT FLUID : Changing
INFOID:0000000001115875
1.
Remove drain plug, and then drain CVT fluid from oil pan.
2.
Install drain plug to oil pan.
CAUTION:
Never reuse drain plug gasket.
3.
Fill CVT fluid from CVT fluid charging pipe to the specified level.
4.
With the engine warmed up, drive the vehicle in an urban area. When ambient temperature is 20
°
C
(68
°
F), it takes about 10 minutes for the CVT fluid to warm up to 50 to 80
°
C (122 to 176
°
F).
5.
Check CVT fluid level and condition.
6.
Repeat steps 1 to 5 if CVT fluid has been contaminated.
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Never mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT
durability, and may damage the CVT, which is not covered by the warranty.
• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Sufficiently shake the container of CVT fluid before using.
SCIA1932E
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
CVT fluid become
degraded due to
high temperatures.
Replace the CVT fluid and check the
CVT main unit and the vehicle for
malfunctions (wire harnesses, cool-
er pipes, etc.)
Milky white or
cloudy
Water in the fluid
Replace the CVT fluid and check for
places where water is getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
CVT
Replace the CVT fluid and check for
improper operation of the CVT.
ATA0022D
Drain plug – tightening torque
: Refer to
CVT fluid
: Refer to
.
Fluid capacity
: Refer to
.
CHASSIS MAINTENANCE
MA-57
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Delete CVT fluid deterioration date with CONSULT-III after changing CVT fluid.
GEAR OIL: RS5F92R
GEAR OIL: RS5F92R : Inspection
INFOID:0000000001095729
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Never start engine while checking oil level.
2.
Set a new gasket on filler plug and then install it to transaxle
case.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque.
GEAR OIL: RS5F92R : Draining
INFOID:0000000001095727
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and then drain gear oil.
3.
Set a new gasket on drain plug and install it to clutch housing.
Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
GEAR OIL: RS5F92R : Refilling
INFOID:0000000001095728
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified limit at filler plug hole as shown.
2.
After refilling gear oil, check oil level. Refer to
3.
Set a new gasket on filler plug and then install it to transaxle
case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
GEAR OIL: RS6F94R
GEAR OIL: RS6F94R : Inspection
INFOID:0000000001095732
LEAKAGE
SCIA7119E
PCIB1504E
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
SCIA7119E
MA-58
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Never start engine while checking oil level.
2.
Set a new gasket on filler plug (1) and then install it to transaxle
case.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque.
GEAR OIL: RS6F94R : Draining
INFOID:0000000001095730
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and then drain gear oil.
3.
Set a new gasket on drain plug (1) and install it to clutch hous-
ing. Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
GEAR OIL: RS6F94R : Refilling
INFOID:0000000001095731
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified limit at filler plug hole as shown.
2.
After refilling gear oil, check oil level. Refer to
3.
Set a new gasket on filler plug (1) and then install it to transaxle
case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
GEAR OIL: RS6F52A
GEAR OIL: RS6F52A : Inspection
INFOID:0000000001095739
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
SCIA7623E
SCIA7622E
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
SCIA7623E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст