Nissan Qashqai (2007-2010). Manual — part 604
TRANSAXLE ASSEMBLY
TM-351
< REMOVAL AND INSTALLATION >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000000914726
2WD : Removal and Installation
INFOID:0000000000914727
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove air breather hose. Refer to
3.
Remove air duct (inlet). Refer to
.
4.
Remove battery. Refer to
1.
CVT fluid level gauge
2.
CVT fluid charging pipe
3.
O-ring
4.
Transaxle assembly
5.
Air breather hose
A.
For tightening torque, refer to
TM-351, "2WD : Removal and Installation"
.
Refer to
for symbols not descrived on the above.
JPDIA0103GB
TM-352
< REMOVAL AND INSTALLATION >
[CVT: RE0F10A]
TRANSAXLE ASSEMBLY
5.
Disconnect connectors (A) and then remove bracket (1).
6.
Remove air cleaner case. Refer to
.
7.
Drain engine coolant.
8.
Remove CVT fluid level gauge.
9.
Remove CVT fluid charging pipe from transaxle assembly.
10. Remove O-ring from CVT fluid charging pipe.
11. Disconnect fluid cooler hose from transaxle assembly. Refer to
TM-348, "FLUID COOLER : Exploded
12. Disconnect following harness connector and wire harness.
• CVT unit harness connector (A).
• Primary speed sensor harness connector (B).
• Secondary speed sensor harness connector (C).
• PNP switch connector (D).
13. Remove harness and clip from the transaxle assembly.
14. Remove CVT water hose. Refer to
.
15. Remove control cable from transaxle assembly. Refer to
16. Remove starter motor. Refer to
.
17. Remove engine under cover with power tool.
18. Turn crankshaft, and remove the four tightening nuts (
) for
drive plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
19. Remove exhaust front tube. Refer to
20. Remove front drive shafts. Refer to
21. Remove suspension member from vehicle. Refer to
22. Support transaxle assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to collide against the drain plug.
23. Support engine assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to collide against the drain plug.
24. Remove engine mounting insulator (LH). Refer to
.
25. Remove bolts fixing transaxle assembly to engine assembly.
26. Remove transaxle assembly from vehicle.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure transaxle assembly to a transmission jack.
27. Remove heater thermostat. Refer to
.
INSTALLATION
Note following, and install the removed parts in the reverse order of the removal.
CAUTION:
JPDIA0240ZZ
JPDIA0113ZZ
JPDIA0114ZZ
TRANSAXLE ASSEMBLY
TM-353
< REMOVAL AND INSTALLATION >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Check fitting of dowel pin (
) when installing transaxle
assembly to engine assembly.
• When installing Transaxle assembly to the engine assembly,
attach the fixing bolts in accordance with the following.
• Set and screw in the drive plate location guide (commercial service
tool: 31197CA000) (A) onto the stud bolts for the torque converter
locate.
• When not using drive plate location guide, rotate torque converter
so that the stud bolt (A) for mounting the drive plate location guide
of torque converter aligns with the mounting position of starter
motor.
JPDIA0116ZZ
A
: Transaxle to engine
B
: Engine to transaxle
JPDIA0117ZZ
Bolt No.
A
B
Number of bolts
2
7
Bolt length “
” mm (in)
55 (2.17)
50 (1.97)
Tightening torque N·m (kg-m, ft-lb)
62 (6.3, 46)
SCIA6616J
SCIA7261J
TM-354
< REMOVAL AND INSTALLATION >
[CVT: RE0F10A]
TRANSAXLE ASSEMBLY
• Rotate crankshaft so that the hole (A) for inserting drive plate loca-
tion guide of drive plate aligns with the mounting position (B) of
starter motor.
NOTE:
When not using drive plate location guide, insert stud bolt of torque
converter into the hole of drive plate, aligning the drive plate hole
position and torque converter.
CAUTION:
Note that the stud bolt strikes the drive plate hole position is
not aligned the torque converter stud bolt.
• Align the position of tightening nuts (
) for drive plate with those
of the torque converter, and temporarily tighten the nuts. Then,
tighten the bolts with the specified torque.
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• When tightening the tightening nuts for the torque converter
after fixing the crankshaft pulley bolts, confirm the tightening
torque of the crankshaft pulley mounting bolts. Refer to
163, "Removal and Installation"
.
• After converter is installed to drive plate, rotate crankshaft several turns and check that transaxle
rotates freely without binding.
2WD : Inspection
INFOID:0000000000914728
INSPECTION BE FORE INSTALLATION
• After inserting a torque converter to the CVT, check distance (A)
with in the reference value limit.
INSPECTION AFTER INSTALLATION
• After completing installation, check the following item.
- CVT fluid leakage and CVT fluid level. Refer to
- CVT position. Refer to
TM-324, "Inspection and Adjustment"
4WD
4WD : Exploded View
INFOID:0000000001116416
SCIA6617J
:51 N·m (5.2 kg-m,38 ft-lb)
JPDIA0114ZZ
B
: Scale
C
: Straightedge
Distance (A)
: Refer to
TM-362, "Removal and Installa-
JPDIA0115ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст